CHAPTER 44 REFERENCED STANDARDS

450—20:

Performance Rating Method for Mulled Combination Assemblies, Composite Units, and Other Mulled Fenestration Systems

R609.8

506—16:

Voluntary Specifications for Impact and Cycle Testing of Fenestration Products

R609.6.1

711—20:

Specification for Self-Adhering Flashing Used for Installation of Exterior Wall Fenestration Products

R703.4

712—14:

Voluntary Specification for Mechanically Attached Flexible Flashing

R703.4

714—19:

Voluntary Specification for Liquid-Applied Flashing Used to Create a Water-Resistive Seal around Exterior Wall Openings in Buildings

R703.4

AAMA/NSA 2100—19:

Specifications for Sunrooms

R301.2.1.1.1

AAMA/WDMA/CSA 101/I.S.2/A440—17:

North American Fenestration Standard/Specification for Windows, Doors, and Skylights

R308.6.9, R609.3

ANSI/ACCA 1 Manual D—2016:

Residential Duct Systems

Table R301.2, M1601.1, M1602.2

ANSI/ACCA 2 Manual J—2016:

Residential Load Calculation

M1401.3

ANSI/ACCA 3 Manual S—2014:

Residential Equipment Selection

M1401.3

318—19:

Building Code Requirements for Structural Concrete

R402.2, Table R404.1.2(2), Table R404.1.2(5), Table R404.1.2(6), Table R404.1.2(7), Table R404.1.2(8), R404.1.3, R404.1.3.1, R404.1.3.3, R404.1.3.4, R404.1.4.2, R404.5.1, R608.1, R608.1.1, R608.1.2, R608.2, R608.5.1, R608.6.1, R608.8.2, R608.9.2, R608.9.3

332—20:

Residential Code Requirements for Structural Concrete

R402.2, R403.1, R404.1.3, R404.1.3.4, R404.1.4.2, R506.1

AISI S100—16 (2020) w/S2—20:

North American Specification for the Design of Cold-Formed Steel Structural Members, 2016 Edition (Reaffirmed 2020), with Supplement 2, 2020 Edition

R608.9.2, R608.9.3

AISI S220—20:

North American Standard for Cold-Formed Steel Nonstructural Framing, 2020

R702.3.3

AISI S230—19:

Standard for Cold-Formed Steel Framing—Prescriptive Method for One- and Two-Family Dwellings, 2019 edition

R301.1.1, R301.2.1.1, R301.2.2.7, R301.2.2.8, R603.6, R603.9.4.1, R603.9.4.2, Figure 608.9(11), R608.9.2, R608.9.3, R608.10

AISI S240—20:

North American Standard for Cold-Formed Steel Structural Framing, 2020

R505.1.3, R603.6, R702.3.3, R804.3.6

ANSI/AMCA 210-ANSI/ASHRAE 51—16:

Laboratory Methods of Testing Fans for Aerodynamic Performance Rating

Table M1504.2, M1505.3

A108.1A—17:

Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar

R702.4.1

A108.1B—2017:

Installation of Ceramic Tile on a Cured Portland Cement Mortar Setting Bed with Dry-Set or Latex Portland Cement Mortar

R702.4.1

A108.4—09:

Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-setting Epoxy Adhesive

R702.4.1

A108.5—20:

Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-Portland Cement Mortar

R702.4.1

A108.6—99 (Reaffirmed 2019):

Installation of Ceramic Tile with Chemical Resistant, Water Cleanable Tile-Setting and -Grouting Epoxy

R702.4.1

A108.11—10:

Interior Installation of Cementitious Backer Units

R702.4.1

A118.1—18:

American National Standard Specifications for Dry-set Portland Cement Mortar

R702.4.1

A118.3—13:

American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy and Water Cleanable Tile-setting Epoxy Adhesive

R702.4.1

A118.4—18:

American National Standard Specifications for Modified Dry-set Cement Mortar

R606.2.11

A118.10—14:

Specification for Load-bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation

P2709.2, P2709.2.4

A136.1—20:

American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile

R702.4.1

A137.1—19:

American National Standard Specifications for Ceramic Tile

R702.4.1

ANSI 117—2020:

Standard Specification for Structural Glued Laminated Timber of Softwood Species

R502.1.3, R602.1.3, R802.1.3

ANSI/CSA FC 1—2014:

Fuel Cell Technologies—Part 3-100: Stationary Fuel Cell Power Systems—Safety

M1903.1

ANSI LC 1—2018/CSA 6.26—2016:

Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST)

G2411.3, G2414.4.4, G2415.5

ANSI LC 4—2012/CSA 6.32—2012:

Press-Connect Metallic Fittings for Use in Fuel Gas Distribution Systems

G2414.9.1, G2414.9.2, G2414.9.3, G2415.5

ANSI Z21.1—2016/CSA 1.1—2016:

Household Cooking Gas Appliances

M1503.2, G2447.1

ANSI Z21.5.1—2017/CSA 7.1—2017:

Gas Clothes Dryers—Volume I—Type 1 Clothes Dryers

G2438.1

ANSI Z21.8—1994 (R2017):

Installation of Domestic Gas Conversion Burners

G2443.1

ANSI Z21.10.1—2017/CSA 4.1—2017:

Gas Water Heaters, Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu per hour or Less

G2448.1

Z21.10.3/CSA 4.3—2017:

Gas Water Heaters—Volume III—Storage Water Heaters with Input Ratings above 75,000 Btu per hour, Circulating and Instantaneous

G2448.1

ANSI Z21.11.2—2016:

Gas-Fired Room Heaters, Volume II, Unvented Room Heaters

G2445.1

ANSI Z21.13—2017/CSA 4.9—2017:

Gas-Fired Low-pressure Steam and Hot Water Boilers

G2452.1

ANSI Z21.15—2009/CSA 9.1—2009 (2014):

Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves

Table G2420.1.1

ANSI Z21.22—2015:

Relief Valves for Hot Water Supply Systems

P2804.2, P2804.7

ANSI Z21.24—2015/CSA 6.10—2015:

Connectors for Gas Appliances

G2422.1, G2422.2

ANSI 40.11—1996 (R2017)/CGA 2.91—M96 (R2017):

Gas-Fired, Heat-Activated Air-Conditioning and Heat Pump Appliances

G2449.1

ANSI Z21.40.2—1996 (R2017)/CGA 2.92—M96 (R2017):

Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Internal Combustion)

G2449.1

ANSI Z21.41—2014/CSA 6.9—2014:

Quick Disconnect Devices for Use with Gas Fuel Appliances

G2422.1

ANSI Z21.42—2013:

Gas-Fired Illuminating Appliances

G2450.1

ANSI Z21.47—2016/CSA 2.3—2016:

Gas-Fired Central Furnaces

G2442.1

ANSI Z21.50—2016/CSA 2.22—2016:

Vented Decorative Gas Fireplaces

G2434.1

ANSI Z21.54—2014/CSA 8.4—2014:

Gas Hose Connectors For Portable Outdoor Gas-Fired Appliances

G2422.1

ANSI Z21.56—2017/CSA 4.7—2017:

Gas-Fired Pool Heaters

G2441.1

ANSI Z21.58—2018/CSA 1.6—2018:

Outdoor Cooking Gas Appliances

G2447.1

ANSI Z21.60—2017/CSA 2.26—2017:

Decorative Gas Appliances for Installation in Solid-Fuel-Burning Fireplaces

G2432.1

ANSI Z21.69—2015/CSA 6.16—2015:

Connectors for Moveable Gas Appliances

G2422.1.5

ANSI Z21.75—2016/CSA 6.27—2016:

Connectors for Outdoor Gas Appliances and Manufactured Homes

G2422.1

ANSI Z21.80—2011/CSA 6.22—2011 (R2016):

Line Pressure Regulators

G2421.1

ANSI Z21.84—2017:

Standard for Manually Lighted, Natural Gas, Decorative Gas Appliances for Installation in Solid-FuelBurning Appliances

G2432.1, G2432.2

ANSI Z21.86—2016/CSA 2.32—2016:

Vented Gas-Fired Space Heating Appliances

G2436.1, G2437.1, G2446.1

ANSI Z21.88—2016/CSA 2.33—2016:

Vented Gas Fireplace Heaters

G2435.1

ANSI Z21.90—2015/CSA 6.24—2015:

Gas Convenience Outlets and Optional Enclosures

G2422.1

ANSI Z21.91—2017:

Ventless Firebox Enclosures for Gas-Fired Unvented Decorative Room Heaters

G2445.7.1

ANSI Z21.93—2017/CSA 6.30—2017:

Excess Flow Valves For Natural Gas and Propane Gas With Pressures Up To 5 Psig

G2421.4

ANSI Z21.97—2017/CSA 2.41—2017:

Outdoor Decorative Gas Appliances

G2453.1

Z83.6—90 (R1998):

Gas-fired Infrared Heaters

G2451.1

ANSI Z83.8—2016/CSA 2.6—2016:

Gas Unit Heater, Gas Packaged Heaters, Gas Utility Heaters And Gas-Fired Duct Furnaces

G2444.1

ANSI Z83.19—2017/CSA 2.35—2017:

Gas-Fired High-Intensity Infrared Heaters

G2451.1

ANSI Z83.20—2016/CSA 2.34—2016:

Gas-Fired Tubular and Low-Intensity Infrared Heaters

G2451.1

Z97.1—2017:

Safety Glazing Materials Used in Buildings—Safety Performance Specifications and Methods of Test

R308.1.1, R308.3.1

ANSI/A190.1—2017:

Structural Glued-laminated Timber

R502.1.3, R602.1.3, R802.1.2

ANSI/APA PRG 320—2019:

Standard for Performance-rated Cross Laminated Timber

R502.1.6, R602.1.6, R802.1.6

ANSI/APA PRP 210—2019:

Standard for Performance-rated Engineered Wood Siding

R604.1, Table R703.3(1), R703.3.4

ANSI/APA PRR 410—2016:

Standard for Performance-rated Engineered Wood Rim Boards

R502.1.7, R602.1.7, R802.1.7

ANSI/APA PRS 610.1—2018:

Standard for Performance-Rated Structural Insulated Panels in Wall Applications

R602.1.11, R610.3, R610.4

APA E30—19:

Engineered Wood Construction Guide

Table R503.2.1.1(1), R503.2.2, R803.2.2, R803.2.3

7—16 with Supplement 1:

Minimum Design Loads and Associated Criteria for Buildings and Other Structures

Table R608.7(1A), Table R608.7(1B), Table R608.7(1C), R301.2.1.1, R301.2.1.2, R301.2.1.2.1, R301.2.1.5, R301.2.1.5.1, Table R608.6(1), Table R608.6(2), Table R608.6(3), Table R608.6(4), R608.9.2, R608.9.3, R609.2, R609.6.2

24—14:

Flood-resistant Design and Construction

R301.2.4, R301.2.4.1, R322.1, R322.1.1, R322.1.6, R322.1.9, R322.2.2, R322.3.3

32—01:

Design and Construction of Frost-protected Shallow Foundations

R403.1.4.1

ASHRAE 34—2019:

Designation and Safety Classification of Refrigerants

M1411.1

ASHRAE—2017:

ASHRAE Handbook of Fundamentals

P3001.2, P3101.4

A18.1—2020:

Safety Standard for Platforms and Stairway Chair Lifts

R321.2

A112.1.2—2012(R2017):

Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water Connected Receptors)

P2717.1, Table P2902.3, P2902.3.1

A112.1.3—2000 (R2019):

Air Gap Fittings for Fixtures, Appliances and Appurtenances

Table P2701.1, P2717.1, Table P2902.3, P2902.3.1

A112.3.1—2007(R2017):

Stainless Steel Drainage Systems for Sanitary, DWV, Storm and Vacuum Applications Above and Below Ground

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table P3302.1

A112.3.4—2018/CSA B45.9—2018:

Macerating Toilet Systems and Related Components

Table P2701.1, P3007.5

A112.4.1—2019:

Water Heater Relief Valve Drain Tubes

P2804.6.1

A112.4.3—1999(R2020):

Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System

P3003.14

A112.4.4—2017:

Plastic Push-Fit Drain, Waste, and Vent (DWV) Fittings

Table P3002.3, P3003.9.4

A112.4.14—2019/CSA B125.14—19:

Manually Operated Valves for Use in Plumbing Systems

Table P2903.9.4

A112.6.2—2017:

Framing-affixed Supports for Off-the-floor Water Closets with Concealed Tanks

Table P2701.1, P2702.4

A112.6.3—2019:

Floor and Trench Drains

Table P2701.1

A112.14.1—03(2017):

Backwater Valves

P3008.3

A112.18.1—2018/CSA B125.1—2018:

Plumbing Supply Fittings

Table P2701.1, P2708.5, P2722.1, P2722.3, P2902.2, Table P2903.9.4

A112.18.2—2020/CSA B125.2—2020:

Plumbing Waste Fittings

Table P2701.1, P2702.2

A112.18.3M—2002(R2017):

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

P2708.5, P2722.3

A112.18.6—2017/CSA B125.6—2017:

Flexible Water Connectors

P2906.7

A112.19.1—2018/CSA B45.2—2018:

Enameled Cast-iron and Enameled Steel Plumbing Fixtures

Table P2701.1, P2711.1

A112.19.2—2018/CSA B45.1—2018:

Ceramic Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1, P2712.2, P2712.9

A112.19.3—2017/CSA B45.4—2017:

Stainless Steel Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1

A112.19.5—2017/CSA B45.15—2017:

Flush Valves and Spuds for Water-closets, Urinals and Tanks

Table P2701.1

A112.19.7—2012/CSA B45.10—2012(2017):

Hydromassage Bathtub Systems

Table P2701.1

A112.19.12—2014(R2019):

Wall-mounted and Pedestal-mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory and Sink, and Shampoo Bowl Carrier Systems and Drain Waste Systems

Table P2701.1, P2711.4, P2714.2

A112.19.14—2013(R2018):

Six-Liter Water Closets Equipped with Dual Flushing Device

P2712.1

A112.19.15—2012(R2017):

Bathtub/Whirlpool Bathtubs with Pressure-sealed Doors

Table P2701.1, P2713.2

A112.36.2M—1991(R2017):

Cleanouts

P3005.2.10.2

ASME A17.1—2019/CSA B44—2019:

Safety Code for Elevators and Escalators

R321.1

ASME A112.4.2—2015/CSA B45.16—2015(R2020):

Water-closet Personal Hygiene Devices

P2722.5

ASSE 1002—2020/ASME A112.1002—2020/CSA B125.12—20:

Anti-Siphon Fill Valves

Table P2701.1, Table P2902.3, P2902.4.1

ASSE 1016—2017/ASME A112.1016—2017/CSA B125.16—2017:

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table P2701.1, P2708.4, P2722.2

ASSE 1070—2020/ASME A112.1070—2020:

Performance Requirements for Water-temperature-limiting Devices

P2713.3, P2721.2

B1.20.1—2013(R2018):

Pipe Threads, General-purpose (Inch)

G2414.9, P3003.3.3, P3003.6.4, P3003.7.1, P3003.9.3

B16.3—2016:

Malleable-iron-threaded Fittings, 150 and 300

Table P2906.6

B16.4—2016:

Gray-iron-threaded Fittings

Table P2906.6, Table P3002.3

B16.9—2018:

Factory-made, Wrought-steel Buttwelding Fittings

Table P2906.6

B16.11—2016:

Forged Fittings, Socket-welding and Threaded

Table P2906.6

B16.12—2009(R2014):

Cast-iron-threaded Drainage Fittings

Table P3002.3

B16.15—2018:

Cast Alloy Threaded Fittings: Classes 125 and 250

Table P2906.6, Table P3002.3

B16.18—2018:

Cast-copper-alloy Solder Joint Pressure Fittings

Table P2906.6, Table P3002.3

B16.22—2018:

Wrought-copper and Copper-alloy Solder Joint Pressure Fittings

Table P2906.6, Table P3002.3

B16.23—2016:

Cast-copper-alloy Solder Joint Drainage Fittings (DWV)

Table P3002.3

B16.26—2018:

Cast-copper-alloy Fittings for Flared Copper Tubes

Table P2906.6, Table P3002.3

B16.28—1994:

Wrought-steel Buttwelding Short Radius Elbows and Returns

Table P2906.6

B16.29—2017:

Wrought-copper and Wrought-copper-alloy Solder Joint Drainage Fittings (DWV)

Table P3002.3

B16.33—2012(R2017):

Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes ¹/₂ through 2)

Table G2420.1.1

B16.34—2017:

Valves—Flanged, Threaded and Welding End

Table P2903.9.4

B16.44—2012(R2017):

Manually Operated Metallic Gas Valves for Use in Above-ground Piping Systems up to 5 psi

Table G2420.1.1

B16.51—2018:

Copper and Copper Alloy Press-Connect Pressure Fittings

Table M2101.1, M2103.3, Table P2906.6

B36.10M—2018:

Welded and Seamless Wrought-steel Pipe

G2414.4.2

BPVC—2019:

ASME Boiler and Pressure Vessel Code (Sections I, II, IV, V, VI and VIII)

M2001.1.1, G2452.1

CSD-1—2018:

Controls and Safety Devices for Automatically Fired Boilers

M2001.1.1, G2452.1

1001—2017:

Performance Requirements for Atmospheric-type Vacuum Breakers

Table P2902.3, P2902.3.2

1003—2009:

Performance Requirements for Water-pressure-reducing Valves for Domestic Water Distribution Systems

P2903.3.1

1008—2006:

Performance Requirements for Plumbing Aspects of Residential Food Waste Disposer Units

Table P2701.1

1010—2004:

Performance Requirements for Water Hammer Arresters

P2903.5

1011—2017:

Performance Requirements for Hose Connection Vacuum Breakers

Table P2902.3, P2902.3.2

1012—2009:

Performance Requirements for Backflow Preventers with an Intermediate Atmospheric Vent

Table P2902.3, P2902.3.3, P2902.5.1, P2902.5.5.3

1013—2011:

Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers

Table P2902.3, P2902.3.5, P2902.5.1, P2902.5.5.3

1015—2011:

Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

Table P2902.3, P2902.3.6

1017—2009:

Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems

P2724.1, P2802.1, P2803.2

1018—2001:

Performance Requirements for Trap Seal Primer Valves—Potable Water Supplied

P3201.2.1.1, P3201.2.1.2

1019—2011(R2016):

Performance Requirements for Wall Hydrant with Backflow Protection and Freeze Resistance

Table P2701.1, Table P2902.3, P2902.3.2

1020—2004:

Performance Requirements for Pressure Vacuum Breaker Assembly

Table P2902.3, P2902.3.4

1023—1979:

Performance Requirements for Hot Water Dispensers, Household-storage-type—Electrical

Table P2701.1

1024—2017:

Performance Requirements for Dual Check Backflow Preventers

Table P2902.3, P2902.3.7

1035—2008:

Performance Requirements for Laboratory Faucet Backflow Preventers

Table P2902.3, P2902.3.2

1044—2015:

Performance Requirements for Trap Seal Primer Drainage Types and Electric Design Types

P3201.2.1.3

1047—2011:

Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies

Table P2902.3, P2902.3.5

1048—2011:

Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies

Table P2902.3, P2902.3.6

1050—2009:

Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems

P3114.1

1051—2009:

Performance Requirements for Individual and Branch-type Air Admittance Valves for Sanitary Drainage Systems

P3114.1

1052—2016:

Performance Requirements for Hose Connection Backflow Preventers

Table P2701.1, Table P2902.3, P2902.3.2

1056—2013:

Performance Requirements for Spill-resistant Vacuum Breaker Assemblies

Table P2902.3, P2902.3.4

1060—2017:

Performance Requirements for Outdoor Enclosures for Fluid-conveying Components

P2902.6.1

1061—2015:

Performance Requirements for Push-Fit Fittings

Table P2906.6, P2906.21

1062—2017:

Performance Requirements for Temperature-actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings

Table P2701.1, P2724.2

1066—1997:

Performance Requirements for Individual Pressure Balancing In-line Valves for Individual Fixture Fittings

P2722.4

1072—2007:

Performance Requirements for Barrier-type Floor Drain Trap Seal Protection Devices

P3201.2.1.4

1081—2014:

Performance Requirements for Backflow Preventers with Integral Pressure Reducing Boiler Feed Valve and Intermediate Atmospheric Vent Style for Domestic and Light Commercial Water Distribution Systems

Table P2902.3, P2902.3.3

ASSE 1002—2020/ASME A112.1002—2020/CSA B125.12—20:

Anti-Siphon Fill Valves for Water Closet Tanks

Table P2701.1, Table P2902.3, P2902.4.1

ASSE 1016—2017/ASME 112.1016—2017/CSA B125.16—2017:

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table P2701.1, P2708.4, P2722.2

ASSE 1037—2015/ASME A112.1037—2015/CSA B125.37—15:

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

Table P2701.1

ASSE 1070—2020/ASME A112.1070—2020/ CSA B125.70—20:

Performance Requirements for Water-temperature-limiting Devices

P2713.3, P2721.2, P2724.1

A36/A36M—14:

Specification for Carbon Structural Steel

R608.5.2.2

A53/A53M—2018:

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

R407.3, Table M2101.1, G2414.4.2, Table P2906.4, Table P2906.5, Table P3002.1(1)

A74—2017:

Specification for Cast-iron Soil Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3005.2.6, Table P3302.1

A106/A106M—2018:

Specification for Seamless Carbon Steel Pipe for High-temperature Service

Table M2101.1, G2414.4.2

A123/A123M—2017:

Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

Table 507.2.3

A126—04(2014):

Gray Iron Castings for Valves, Flanges and Pipe Fittings

Table P2903.9.4

A153/A153M—2016A:

Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware

R317.3, Table 507.2.3, Table R606.3.4.1, R703.6.3, R905.7.5, R905.8.6

A167—99(2009):

Specification for Stainless and Heat-resisting Chromium-nickel Steel Plate, Sheet and Strip

Table R606.3.4.1

A240/A240M—17:

Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications

Table R905.10.3(1)

A254—2010(2018):

Specification for Copper Brazed Steel Tubing

Table M2101.1, G2414.5.1

A268/A268M—2010(16):

Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service

G2414.5.2

A269/A269M—2015A:

Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service

G2414.5.2

A307—2014E1:

Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength

Table R507.2.3, R608.5.2.2

A312/A312M—2018:

Specification for Seamless, Welded and Heavily Cold Worked Austenitic Stainless Steel Pipes

Table P2906.4, Table P2906.5, Table P2906.6, P2906.13.2

A463/A463M—15:

Standard Specification for Steel Sheet, Aluminum-coated by the Hot-dip Process

Table R905.10.3(2)

A539—99:

Specification for Electric-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines

M2202.1

A563—15:

Standard Specification for Carbon and Alloy Steel Nuts

Table R507.2.3

A615/A615M—2015aE1:

Specification for Deformed and Plain Carbon-steel Bars for Concrete Reinforcement

R402.3.1, R403.1.3.5.1, R404.1.3.3.7.1, R608.5.2.1

A641/A641M—09a(2014):

Specification for Zinc-coated (Galvanized) Carbon Steel Wire

Table R606.3.4.1

A653/A653M—2017:

Specification for Steel Sheet, Zinc-coated Galvanized or Zinc-iron Alloy-coated Galvannealed by the Hot-dip Process

R317.3.1, R505.2.2, Table R507.2.3, R603.2.2, Table R606.3.4.1, R608.5.2.3, R804.2.2, R804.2.3, Table R905.10.3(1), Table R905.10.3(2), M1601.1.1

A706/A706M—2016:

Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement

R402.3.1, R403.1.3.5.1, R404.1.3.3.7.1, R608.5.2.1

A755/A755M—2016E1:

Specification for Steel Sheet, Metallic Coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products

Table R905.10.3(2)

A778/A778M—2016:

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

Table P2906.4, Table P2906.5, Table P2906.6

A792/A792M—10(2015):

Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process

R505.2.2, R603.2.2, R608.5.2.3, R804.2.2, Table 905.10.3(2)

A875/A875M—13:

Specification for Steel Sheet, Zinc-5%, Aluminum Alloy-coated by the Hot-dip Process

R608.5.2.3, Table R905.10.3(2)

A888—2018:

Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Application

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table P3302.1

A924/A924M—2017A:

Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process

Table R905.10.3(1)

A996M—2016:

Specifications for Rail-steel and Axle-steel Deformed Bars for Concrete Reinforcement

R403.1.3.5.1, Table R404.1.2(9), R404.1.3.3.7.1, R608.5.2.1, Table R608.5.4(2)

A1003/A1003M—15:

Standard Specification for Steel Sheet, Carbon, Metallic and Nonmetallic-coated for Cold-formed Framing Members

R505.2.1, R505.2.2, R603.2.1, R603.2.2, R804.2.1, R804.2.2

B32—08(2014):

Specification for Solder Metal

P3003.6.3

B42—2015A:

Specification for Seamless Copper Pipe, Standard Sizes

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1)

B43—15:

Specification for Seamless Red Brass Pipe, Standard Sizes

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1)

B75/B75M—11:

Specification for Seamless Copper Tube

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1), Table P3002.1(2), Table P3002.2

B88—2016:

Specification for Seamless Copper Water Tube

Table M2101.1, G2414.5.2, Table P2906.4, Table P2906.5, Table P3002.1(1), Table P3002.1(2), Table P3002.2

B101—12:

Specification for Lead-coated Copper Sheet and Strip for Building Construction

Table R905.2.8.2, Table R905.10.3(1)

B135/B135M—2017:

Specification for Seamless Brass Tube

Table M2101.1

B209—14:

Specification for Aluminum and Aluminum-alloy Sheet and Plate

Table 905.10.3(1)

B251/B251M—2017:

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1), Table P3002.1(2), Table P3002.2

B280—2018:

Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

G2414.4.3

B302—2017:

Specification for Threadless Copper Pipe, Standard Sizes

Table M2101.1, Table P2906.4, Table P2906.5, Table P3002.1(1)

B306—13:

Specification for Copper Drainage Tube (DWV)

Table M2101.1, Table P3002.1(1), Table P3002.1(2)

B370—12:

Specification for Copper Sheet and Strip for Building Construction

Table R905.2.8.2, Table R905.10.3(1), Table P2701.1

B447—12a:

Specification for Welded Copper Tube

Table P2906.4, Table P2906.5

B695—2004(2016):

Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

R317.3.1, R317.3.3, Table R507.2.3

B813—2016:

Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube

Table M2101.1, M2103.3, P2906.15, P3003.6.3

B828—2016:

Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

M2103.3, P2906.15, P3003.6.3

C4—2004(2018):

Specification for Clay Drain Tile and Perforated Clay Drain Tile

Table P3302.1

C5—2018:

Specification for Quicklime for Structural Purposes

R702.2.1

C14—15a:

Specification for Non-reinforced Concrete Sewer, Storm Drain and Culvert Pipe

Table P3002.2

C22/C22M—2015:

Specification for Gypsum

R702.2.1, R702.3.1

C27—1998(2018):

Specification for Standard Classification of Fireclay and High-alumina Refractory Brick

R1001.5

C28/C28M—10(2015):

Specification for Gypsum Plasters

R702.2.1

C33/C33M—2018:

Specification for Concrete Aggregates

R403.4.1

C34—2017:

Specification for Structural Clay Load-bearing Wall Tile

Table R301.2, R606.2.2

C35/C35M—01(2014):

Specification for Inorganic Aggregates for Use in Gypsum Plaster

R702.2.1

C55—2017:

Specification for Concrete Building Brick

R202, Table R301.2, R606.2.1

C56—2013(2017):

Standard Specification for Structural Clay Nonloadbearing Tile

R606.2.2

C59/C59M—00(2015):

Specification for Gypsum Casting Plaster and Molding Plaster

R702.2.1

C61/C61M—00(2015):

Specification for Gypsum Keene’s Cement

R702.2.1

C62—2017:

Standard Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)

R202, Table R301.2, R606.2.2

C73—2017:

Specification for Calcium Silicate Face Brick (Sand Lime Brick)

R202, Table R301.2, R606.2.1

C76—2018A:

Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

Table P3002.2

C90—2016A:

Specification for Load-bearing Concrete Masonry Units

Table R301.2, 606.2.1

C91/C91M—2018:

Specification for Masonry Cement

R702.2.2, R703.7.2

C94/C94M—2017A:

Standard Specification for Ready-mixed Concrete

R404.1.3.3.2, R608.5.1.2

C126—2017:

Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

R606.2.2

C129—2017:

Specification for Nonload-bearing Concrete Masonry Units

Table R301.2

C143/C143M—15A:

Test Method for Slump of Hydraulic Cement Concrete

R404.1.3.3.4, R608.5.1.4

C145—85:

Specification for Solid Load-bearing Concrete Masonry Units

R202, Table R301.2

C150/C150M—2018:

Specification for Portland Cement

R608.5.1.1, R702.7.2

C199—1984(2016):

Test Method for Pier Test for Refractory Mortar

R1001.5, R1001.8, R1003.12

C207—2018:

Specification for Hydrated Lime for Masonry Purposes

Table R606.2.8

C208—2012(2017)E1:

Specification for Cellulosic Fiber Insulating Board

R602.1.10, Table R602.3(1), Table R906.2

C212—2017:

Standard Specification for Structural Clay Facing Tile

R606.2.2

C216—2017A:

Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

R202, Table R301.2, R606.2.2

C270—14A:

Specification for Mortar for Unit Masonry

R606.2.8, Table R606.2.8, R606.2.11

C315—2007(2016):

Specification for Clay Flue Liners and Chimney Pots

R1001.8, R1003.11.1, Table R1003.14(1), G2425.12

C406/C406M—2015:

Specifications for Roofing Slate

R905.6.4

C411—2017:

Test Method for Hot-surface Performance of High-temperature Thermal Insulation

M1601.3

C425—2004(2018):

Specification for Compression Joints for Vitrified Clay Pipe and Fittings

Table P3002.2, P3003.10, P3003.13

C443—2012(2017):

Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

P3003.5, P3003.13

C475/C475M—2017:

Specification for Joint Compound and Joint Tape for Finishing Gypsum Board

R702.3.1

C476—2018:

Specification for Grout for Masonry

R606.2.12

C503M—2015:

Standard Specification for Marble Dimension Stone

R606.2.4

C514—04(2014):

Specification for Nails for the Application of Gypsum Wallboard

R702.3.1

C552—2017E1:

Standard Specification for Cellular Glass Thermal Insulation

Table R906.2

C557—2003(2017):

Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

R702.3.1.1

C564—14:

Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

P3003.4.2, P3003.4.3, P3003.13

C568M—2015:

Standard Specification for Limestone Dimension Stone

R606.2.4

C578—2018:

Specification for Rigid, Cellular Polystyrene Thermal Insulation

R316.8, R403.3, Table 703.8.4(2), Table R703.15.1, Table R703.15.2, Table R703.16.1, Table R703.16.2, Table R906.2

C587—2004(2018):

Specification for Gypsum Veneer Plaster

R702.2.1

C595/C595M—2018:

Specification for Blended Hydraulic Cements

R608.5.1.1, R702.2.2, R703.7.2

C615/C615M—2018E1:

Standard Specification for Granite Dimension Stone

R606.2.4

C616/C616M—2015:

Standard Specification for Quartz-based Dimension Stone

R606.2.4

C629/C629M—2015:

Standard Specification for Slate Dimension Stone

R606.2.4

C631—09(2014):

Specification for Bonding Compounds for Interior Gypsum Plastering

R702.2.1

C645—2018:

Specification for Nonstructural Steel Framing Members

R702.3.3

C652—2017A:

Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)

R202, Table R301.2, R606.2.2

C685/C685M—2017:

Specification for Concrete Made by Volumetric Batching and Continuous Mixing

R404.1.3.3.2, R608.5.1.2

C700—2018:

Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength and Perforated

Table P3002.2, Table P3002.3, Table P3302.1

C726—2017:

Standard Specification for Mineral Wool Roof Insulation Board

Table R906.2

C728—2017A:

Standard Specification for Perlite Thermal Insulation Board

Table R906.2

C744—2016:

Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units

R606.2.1

C836/C836M—2018:

Specification for High Solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

R905.15.2

C841—2003(2018):

Standard Specification for Installation of Interior Lathing and Furring

R702.2.1

C842—05(2015):

Standard Specification for Application of Interior Gypsum Plaster

R702.2.1

C843—2017:

Specification for Application of Gypsum Veneer Plaster

R702.2.1

C844—2015:

Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

R702.2.1

C847—2018:

Specification for Metal Lath

R702.2.1, R702.2.2

C887—13:

Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar

R406.1, R606.2.9

C897—15:

Specification for Aggregate for Job-mixed Portland Cement-based Plasters

R702.2.2

C920—2018:

Standard Specification for Elastomeric Joint Sealants

R406.4.1

C926—2018B:

Specification for Application of Portland Cement-based Plaster

R702.2.2, R702.2.2.1, R703.7, R703.7.2, R703.7.2.1, R703.7.4

C933—2018:

Specification for Welded Wire Lath

R702.2.1, R702.2.2

C946—2018:

Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls

R606.2.9

C954—2018:

Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in (0.84 mm) or to 0.112 in. (2.84 mm) in Thickness

R505.2.5, R603.2.5, R702.3.5.1, R804.2.5

C957/C957M—2017:

Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane with Integral Wearing Surface

R905.15.2

C1002—2018:

Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs

R702.3.1, R702.3.5.1

C1029—15:

Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation

R905.14.2

C1032—2018:

Specification for Woven Wire Plaster Base

R702.2.1, R702.2.2

C1047—2014a:

Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

R702.2.1, R702.2.2, R702.3.1

C1063—2018B:

Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster

R702.2.2, R703.7, R703.7.1

C1088—2018:

Standard Specification for Thin Veneer Brick Units Made from Clay or Shale

R606.2.2

C1107/C1107M—2017:

Standard Specification for Packaged Dry, Hydraulic-cement Grout (Nonshrink)

R402.3.1

C1116/C116M—10(2015):

Standard Specification for Fiber-reinforced Concrete and Shotcrete

R402.3.1

C1157/C1157M—2017:

Standard Performance Specification for Hydraulic Cement

R608.5.1.1, R703.7.2

C1167—2011(2017):

Specification for Clay Roof Tiles

R905.3.4

C1173—2018:

Specification for Flexible Transition Couplings for Underground Piping Systems

P3003.3.1, P3003.5, P3003.9.1, P3003.10, P3003.12.2, P3003.13

C1177/C1177M—2017:

Specification for Glass Mat Gypsum Substrate for Use as Sheathing

R702.3.1, Table 906.2

C1178/C1178M—2018:

Specification for Glass Mat Water-resistant Gypsum Backing Panel

R702.3.1, R702.3.7, Table R702.4.2

C1186—2008(2016):

Specification for Flat Fiber Cement Sheets

R703.10.1, R703.10.2

C1261—2013(2017)E1:

Specification for Firebox Brick for Residential Fireplaces

R1001.5, R1001.8

C1277—2018:

Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

P3003.4.3

C1278/C1278M—2017:

Specification for Fiber-reinforced Gypsum Panels

R702.3.1, R702.3.7, Table R702.4.2, Table R906.2

C1280—13a:

Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing

R602.3(1)

C1283—2015:

Practice for Installing Clay Flue Lining

R1003.9.1, R1003.12

C1288—2017:

Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets

Table R503.2.1.1(1), Table R503.2.1.1(2), Table 602.3(2), Table R702.4.2

C1289—2018:

Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

R316.8, Table R703.15.1, Table R703.15.2, Table R703.16.1, Table R703.16.2, Table R906.2

C1325—2018:

Standard Specification for Fiber-mat Reinforced Cementitious Interior Substrate Sheets Backer Units

Table R702.4.2

C1328/C1328M—12:

Specification for Plastic (Stucco) Cement

R702.2.2, R703.7.2

C1364—2017:

Standard Specification for Architectural Cast Stone

R606.2.5

C1396/C1396M—2017:

Specification for Gypsum Board

Table R602.3(1), R702.2.1, R702.2.2, R702.3.1, R702.3.7

C1405—2016:

Standard Specification for Glazed Brick (Single Fired, Brick Units)

R606.2.2

C1440—2017:

Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

P3003.13

C1460—2017:

Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

P3003.13

C1461—2008(2017):

Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

P3003.13

C1492—2003(2016):

Specification for Concrete Roof Tile

R905.3.5

C1513—2018:

Standard Specification for Steel Tapping Screws for Cold-formed Steel Framing Connections

R505.2.5, R603.2.5, R702.3.5.1, Table R703.3(2), Table R703.16.1, Table R703.16.2, R804.2.5

C1540—2018:

Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-iron Soil Pipe and Fittings

P3003.4.3

C1634—2017:

Standard Specification for Concrete Facing Brick

R606.2.1

C1658/C1658M—2018:

Standard Specification for Glass Mat Gypsum Panels

R702.3.1

C1668—13a:

Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating, Ventilation, and Air Conditioning (HVAC) Systems

M1601.3

C1670/1670M—2018:

Standard Specification for Adhered Manufactured Stone Masonry Veneer Units

R606.2.6

C1691—2011(2017):

Standard Specification for Unreinforced Autoclaved Aerated Concrete (AAC) Masonry Units

R606.2.3

C1693—2011(2017):

Standard Specification for Autoclaved Aerated Concrete (AAC)

R606.2.3

C1766—2015:

Standard Specification for Factory-Laminated Gypsum Panel Products

R702.3.1

D41/D41M—2011(2016):

Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2, Table R905.11.2

D43/D43M—2000(20118):

Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2

D226/D226M—2017:

Specification for Asphalt-saturated (Organic Felt) Used in Roofing and Waterproofing

R703.2, R905.1.1, Table R905.1.1(1), R905.8.4, Table R905.9.2

D227/D227M—2003(2018):

Specification for Coal Tar Saturated (Organic Felt) Used in Roofing and Waterproofing

Table R905.9.2

D312/D312M—2016M:

Specification for Asphalt Used in Roofing

Table R905.9.2

D422—63(2007)E2:

Test Method for Particle-size Analysis of Soils

R403.1.8.1

D449/D449M—03(2014)E1:

Specification for Asphalt Used in Dampproofing and Waterproofing

R406.2

D450/D450M—2017(2018):

Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing

Table R905.9.2

D1227—13:

Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

Table R905.9.2, Table R905.11.2, R905.15.2

D1248—2016:

Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

M1601.1.2

D1527—99(2005):

Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe, Schedules 40 and 80

Table P2906.4

D1693—15:

Test Method for Environmental Stress-cracking of Ethylene Plastics

Table M2101.1

D1784—11:

Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds

M1601.1.2

D1785—15E1:

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

Table P2906.4

D1863/D1863M—2005(2018):

Specification for Mineral Aggregate Used on Built-up Roofs

Table R905.9.2

D1869—15:

Specification for Rubber Rings for Fiber-Reinforced Cement Pipe

P2906.18, P3003.13

D1970/D1970M—2017A:

Specification for Self-adhering Polymer Modified Bitumen Sheet Materials Used as Steep Roof Underlayment for Ice Dam Protection

R905.1.1, R905.2.8.2, R905.11.2.1

D2104—03:

Specification for Polyethylene (PE) Plastic Pipe, Schedule 40

Table P2906.4

D2178/D2178M—15A:

Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

Table R905.9.2

D2235—2004(2016):

Specification for Solvent Cement for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe and Fittings

P2906.9.1.1, P3003.3.2

D2239—12A:

Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Table P2906.4

D2241—15:

Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)

Table P2906.4

D2282—99(2005):

Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe (SDR-PR)

Table P2906.4

D2412—2011(2018):

Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading

M1601.1.2

D2447—03:

Specification for Polyethylene (PE) Plastic Pipe Schedules 40 and 80, Based on Outside Diameter

Table M2101.1

D2464—15:

Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

D2466—20: 17:

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

Table P2906.6

D2467—15:

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

D2468—96a:

Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe Fittings, Schedule 40

Table P2906.6

D2513—2018A:

Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing and Fittings

Table M2101.1, G2414.6, G2414.6.1, G2414.11, G2415.17.2

D2564—2012(2018):

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

P2906.9.1.4, P3003.9.2

D2609—15:

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

Table P2906.6

D2626/D2626M—04 (2012)e1:

Specification for Asphalt-saturated and Coated Organic Felt Base Sheet Used in Roofing

Table R905.1.1(1), Table R905.9.2

D2657—2007(2015):

Standard Practice for Heat Fusion Joining of Polyolefin Pipe Fittings

M2105.11.1, P2906.3.1, P2906.20.2, P3003.12.1

D2661—14E1:

Specification for Acrylonitrile-butadiene-styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.3.2

D2665—14:

Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3

D2672—14:

Specification for Joints for IPS PVC Pipe Using Solvent Cement

Table P2906.4

D2680—01(2014):

Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping

Table P3002.2

D2683—14:

Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

Table M2105.5, M2105.11.1, P2906.20.2, P3002.3, P3010.5

D2729—2017:

Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

P3009.11, Table P3302.1

D2737—2012A:

Specification for Polyethylene (PE) Plastic Tubing

Table P2906.4

D2751—05:

Specification for Acrylonitrile-butadiene-styrene (ABS) Sewer Pipe and Fittings

Table P3002.2, Table P3002.3

D2822/D2822M—2005(2011):

Specification for Asphalt Roof Cement, Asbestos Containing

Table R905.9.2

D2823/D2823M—05(2011)e1:

Specification for Asphalt Roof Coatings, Asbestos Containing

Table R905.9.2

D2824/D2824M—2018:

Standard Specification for Aluminum-pigmented Asphalt Roof Coatings, Nonfibered and Fibered without Asbestos

Table R905.9.2, Table R905.11.2

D2846/D2846M—2017BE1:

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-water Distribution Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, P2906.9.1.2, P2906.9.1.3

D2855—2015:

Standard Practice for Making Solvent-cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings

P3003.9.2

D2898—2010(2017):

Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing

R802.1.5.4, R802.1.5.8

D2949—10:

Specification for 3.25-in. Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste and Vent Pipe and Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3

D3019/D3019—2017:

Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered

Table R905.9.2, Table R905.11.2

D3034—2016:

Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

Table P3002.2, Table P3002.3

D3035—15:

Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

Table M2105.4

D3138—04(2016):

Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Non-Pressure Piping Components

P3003.13.4

D3161/D3161M—2016A:

Test Method for Wind-Resistance of Steep Slope Roofing Products (Fan Induced Method)

R905.2.4.1, Table R905.2.4.1, R905.16.6

D3201/D3201M—2013:

Test Method for Hygroscopic Properties of Fire-retardant Wood and Wood-base Products

R802.1.5.9

D3212—07(2013):

Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

P3003.3.1, P3003.9.1, P3003.12.2

D3261—2016:

Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

Table M2101.1, Table M2105.5, M2105.11.1, M2105.13.3, P2906.20.2

D3309—96a(2002):

Specification for Polybutylene (PB) Plastic Hot- and Cold-water Distribution System

Table M2101.1

D3311—2017:

Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

P3002.3

D3350—14:

Specification for Polyethylene Plastic Pipe and Fitting Materials

Table M2101.1

D3462/D3462M—2016:

Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

R905.2.4

D3468/D3468M—99(2013)E1:

Specification for Liquid-applied Neoprene and Chlorosulfanated Polyethylene Used in Roofing and Waterproofing

R905.15.2

D3679—2017:

Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

R703.11

D3737—2018E1:

Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

R502.1.3, R602.1.3, R802.1.2

D3747—79(2007):

Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

Table R905.9.2, Table R905.11.2

D3909/D3909M—14:

Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

R905.2.8.2, R905.5.4, Table R905.9.2

D4022/D4022M—2007(2012)e1:

Specification for Coal Tar Roof Cement, Asbestos Containing

Table R905.9.2

D4068—2017:

Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water Containment Membrane

P2709.2, P2709.2.2

D4318—2017E1:

Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils

R403.1.8.1

D4434/D4434M—2015:

Specification for Poly (Vinyl Chloride) Sheet Roofing

R905.13.2

D4479/D4479M—2007(2018):

Specification for Asphalt Roof Coatings—asbestos-free

Table R905.9.2

D4551—2017:

Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-containment Membrane

P2709.2, P2709.2.1

D4586/D4586M—2007(2018):

Specification for Asphalt Roof Cement—asbestos-free

Table R905.9.2

D4601/D4601M—04(2012)e1:

Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing

Table R905.9.2, R905.11.2.1

D4637/D4637M—2015:

Specification for EPDM Sheet Used in Single-ply Roof Membrane

R905.12.2

D4829—11:

Test Method for Expansion Index of Soils

R403.1.8.1

D4869/D4869M—2016A:

Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing

R905.1.1, Table R905.1.1(1)

D4897/D4897M—2016:

Specification for Asphalt Coated Glass-fiber Venting Base Sheet Used in Roofing

Table R905.9.2

D4990—1997a(2013):

Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

Table R905.9.2

D5019—07a:

Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane

R905.12.2

D5055—2016:

Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists

R502.1.2, R802.1.8

D5456—2018:

Standard Specification for Evaluation of Structural Composite Lumber Products

R502.1.5, R602.1.5, R802.1.4

D5516—2018:

Test Method for Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures

R802.1.5.6

D5643/D5643M—2006(2018):

Specification for Coal Tar Roof Cement Asbestos-free

Table R905.9.2

D5664—2017:

Test Methods for Evaluating the Effects of Fire-retardant Treatments and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber

R802.1.5.7

D5665/D5665M—99a(2014)E1:

Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing

Table R905.9.2

D5726—98(2013):

Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing

Table R905.9.2

D6083/D6083M—2018:

Specification for Liquid-applied Acrylic Coating Used in Roofing

Table R905.9.2, Table R905.11.2, Table R905.14.3, R905.15.2

D6162/D6162M—2016:

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

Table R905.11.2

D6163/D6163M—2016:

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

Table R905.11.2

D6164/D6164M—2016:

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

Table R905.11.2

D6222/D6222M—2016:

Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements

Table R905.11.2

D6223/D6223M—2016:

Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcement

Table R905.11.2

D6298—2016:

Specification for Fiberglass-reinforced Styrene Butadiene Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

Table R905.11.2

D6305—08(2015)E1:

Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing

R802.1.5.6

D6380/D6380M—2003(2018):

Standard Specification for Asphalt Roll Roofing (Organic Felt)

Table R905.1.1(1), R905.2.8.2, R905.5.4

D6464—2003A(2017):

Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

R702.3.1.1

D6694/D6694M—08(2013)E1:

Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems

Table R905.14.3, R905.15.2

D6754/D6754M—2015:

Standard Specification for Ketone-ethylene-ester-based Sheet Roofing

R905.13.2

D6757/D6757M—2018:

Specification for Underlayment Felt Containing Inorganic Fibers Used with Steep Slope Roofing

R905.1.1, Table R905.1.1(1)

D6841—2016:

Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber

R802.1.5.7

D6878/D6878M—2017:

Standard Specification for Thermoplastic-polyolefin-based Sheet Roofing

R905.13.2

D6947/D6947M—2016:

Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

Table R905.14.3, R905.15.2

D7032—2017:

Standard Specification for Establishing Performance Ratings for Wood-plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)

R507.2.2, R507.2.2.1, 507.2.2.3, 507.2.2.4

D7158—D7158M—2019:

Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)

R905.2.4.1, Table R905.2.4.1

D7254—2017:

Standard Specification for Polypropylene (PP) siding

Table R703.3(1), R703.14

D7425/D7425M—13:

Standard Specification for Spray Polyurethane Foam Used for Roofing Application

R905.14.2

D7672—2014E1:

Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies

R502.1.7, R602.1.7, R802.1.7

D7793—2017:

Standard Specification for Insulated Vinyl Siding

Table R703.3(1), R703.13

E84—2018B:

Standard Test Method for Surface Burning Characteristics of Building Materials

R202, R302.9.3, R302.9.4, R302.10.1, R302.10.2, R316.3, R316.5.9, R316.5.11, R507.2.2.2, R703.14.3, R802.1.5, M1601.3, M1601.5.2, P2801.6

E96/E96M—2016:

Test Method for Water Vapor Transmission of Materials

R202, Table R806.5, M1411.6, M1601.4.6

E108—2017:

Test Methods for Fire Tests of Roof Coverings

R302.2.4, R902.1

E119—2018B:

Test Methods for Fire Tests of Building Construction and Materials

Table R302.1(1), Table R302.1(2), R302.2.1, R302.2.2, R302.3, R302.4.1, R302.11.1, R606.2.2

E136—2019:

Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 Degrees C

R202, R302.11

E283—2004(2012):

Test Method for Determining the Rate of Air Leakage through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences across the Specimen

R202

E330/E330M—14:

Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference

R609.4, R609.5, R609.6.2, R703.1.2

E331—2000(2016):

Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference

R703.1.1

E814—2013A(2017):

Standard Test Method for Fire Tests of Penetration Firestop Systems

R302.4.1.2

E970—2017:

Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

R302.10.5

E1509—2012(2017):

Standard Specification for Room Heaters, Pellet Fuel-burning Type

M1410.1

E1602—2003(20117):

Guide for Construction of Solid Fuel Burning Masonry Heaters

R1002.2

E1745—17:

Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs

R506.2.3

E1886—2013A:

Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Missle(s) and Exposed to Cyclic Pressure Differentials

R301.2.1.2, R609.6.1, R609.6.2, Table R703.11.2

E1996—2017:

Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

R301.2.1.2, R301.2.1.2.1, R609.6.1, R609.6.2

E2178—2013:

Standard Test Method for Air Permeance of Building Materials

R202

E2231—2018:

Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

M1601.3

E2273—2018:

Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies

R703.9.2

E2556/E2556M—2010(2016):

Standard Specification for Vapor Permeable Flexible Sheet Water-resistive Barriers Intended for Mechanical Attachment

R703.2

E2568—2017A:

Standard Specification for PB Exterior Insulation and Finish Systems

R703.9.1, R703.9.2

E2570/E2570M—07(2014)E1:

Standard Test Methods for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage

R703.9.2

E2634—2018:

Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems

R404.1.3.3.6.1, R608.4.4

E2925—17:

Standard Specification for Manufactured Polymeric Drainage and Ventilation Materials Used to Provide a Rainscreen Function

R703.7.3.2

F405—05:

Specification for Corrugated Polyethylene (PE) Pipe and Fittings

Table P3009.11, Table P3302.1

F409—2017:

Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

Table P2701.1, P2702.2, P2702.3

F437—15:

Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

F438—2017:

Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

Table P2906.6

F439—13:

Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

Table P2906.6

F441/F441M—15:

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

Table P2906.4, Table P2906.5

F442/F442M—13E1:

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

Table P2906.4, Table P2906.5

F477—14:

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

P2906.18, P3003.13

F493—14:

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

P2906.9.1.2, P2906.9.1.3, P2906.18.2

F628—2012E2:

Specification for Acrylonitrile-butadiene-styrene (ABS) Schedule 40 Plastic Drain, Waste and Vent Pipe with a Cellular Core

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.3.2

F656—2015:

Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

P2906.9.1.4, P3003.9.2

F714—13:

Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

Table P3002.1(2), Table P3002.2, P3010.4

F844—07a(2013):

Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use

Table R507.2.3

F876—2017:

Specification for Cross-linked Polyethylene (PEX) Tubing

Table M2101.1, Table P2906.4, Table P2906.5

F877—2018A:

Specification for Cross-linked Polyethylene (PEX) Plastic Hot- and Cold-water Distribution Systems

Table M2101.1, Table P2906.6

F891—2016:

Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3302.1

F1055—2016A:

Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene Pipe and Tubing

Table M2105.5, M2105.11.2, P2906.20.2

F1281—2017:

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

Table M2101.1, P2506.12.1, Table P2906.4, Table P2906.5, Table P2906.6

F1282—2017:

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, P2906.12.1

F1412—2016:

Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.11.1

F1488—14E1:

Specification for Coextruded Composite Pipe

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3009.11

F1504—2014:

Standard Specification for Folded Poly (Vinyl Chloride) (PVC) for Existing Sewer and Conduit Rehabilitation

P3011.4

F1554—2018:

Specification for Anchor Bolts, Steel, 36, 55 and 105-ksi Yield Strength

R608.5.2.2

F1667—2018:

Specification for Driven Fasteners: Nails, Spikes and Staples

R317.3, Table R507.2.3, Table R602.3(1), R703.3.3, R703.6.3, Table R703.15.1, Table R703.15.2, R905.2.5

F1807—2018:

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table M2101.1, Table P2906.6

F1866—2018:

Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

Table P3002.3

F1871—2011:

Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation

P3011.4

F1924—12:

Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

M2105.11.1

F1960—2018:

Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

Table M2101.1, Table P2906.6

F1970—12E1:

Standard Specification for Special Engineered Fittings, Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

M2105.5, Table 2903.9.4

F1973—2013(2018):

Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA 11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems

G2415.17.2

F1974—09(2015):

Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

Table P2906.6, P2906.12.1

F1986—2001(2011):

Specification for Multilayer Pipe, Type 2, Compression Fittings and Compression Joints for Hot and Cold Drinking Water Systems

Table P2906.4, Table P2906.5, Table P2906.6

F2080—2016:

Specification for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (PEX) Pipe

Table P2906.6

F2090—17:

Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms

R310.1.1, R312.2.1, R312.2.2

F2098—2015:

Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings

Table M2101.1, Table P2906.6

F2159—2018:

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table P2906.6

F2262—09:

Standard Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Tubing OD Controlled SDR9

Table P2906.4, Table P2906.5

F2389—2017A:

Standard for Pressure-rated Polypropylene (PP) Piping Systems

Table P2906.4, Table P2906.5, Table P2906.6, P2906.11.1

F2434—14:

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX AL-PEX) Tubing

Table P2906.6

F2623—14:

Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR9 Tubing

Table M2101.1

F2735—2009(2016):

Standard Specification for Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

Table M2101.1, Table P2906.6

F2769—2018:

Polyethylene or Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6

F2806—10(2015):

Standard Specification for Acrylonitrile-butadiene-styrene (ABS) Plastic Pipe (Metric SDR-PR)

Table M2101.1

F2855—12:

Standard Specification for Chlorinated Poly (Vinyl Chloride)/Aluminum/Chlorinated Poly (Vinyl Chloride) (CPVC AL CPVC) Composite Pressure Tubing

Table P2906.4, Table P2906.5

F2945—2018:

Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing and Fittings

G2414.6

F2969—12:

Standard Specification for Acrylonitrile-butadiene-styrene (ABS) IPS Dimensioned Pressure Pipe

Table M2101.1

F3226/F3226M—16:

Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems

Table P2906.6

F3253—2017:

Standard Specification for Crosslinked Polyethylene (PEX) Tubing with Oxygen Barrier for Hot- and Cold-Water Hydronic Distribution Systems

Table M2101.1

ANSI/AWC NDS—2018:

National Design Specification (NDS) for Wood Construction—with 2018 Supplement

R404.2.2, R502.2, Table R503.1, R507.2.1, R602.3, R608.9.2, R608.9.3, Table R703.15.1, Table R703.15.2, R802.2

ANSI/AWC PWF—2021:

Permanent Wood Foundation Design Specification

R317.3.2, R401.1, R404.2.3

ANSI/AWC WFCM—2018:

Wood Frame Construction Manual for One- and Two-family Dwellings

R301.1.1, R301.2.1.1, R602.10.8.2, Figure R608.9(9), R608.9.2, R608.9.3, R608.10

AWC STJR—2021:

Span Tables for Joists and Rafters

R502.3, R802.4.1, R802.5.1

C1—03:

All Timber Products—Preservative Treatment by Pressure Processes

R902.2

M4—15:

Standard for the Care of Preservative-treated Wood Products

R317.1.1, R318.1.2

U1—20:

USE CATEGORY SYSTEM: User Specification for Treated Wood Except Commodity Specification H

R317.1, R402.1.2, R504.3, R703.6.3, R905.7.5, Table R905.8.5, R905.8.6

A5.8M/A5.8—2011—AMD1:

Specification for Filler Metals for Brazing and Braze Welding

P3003.6.1

ANSI/AWS A5.31M/A5.31—2012:

Specification for Fluxes for Brazing and Braze Welding Edition: 2nd

M2103.3, M2202.2, P2906.15

C104/A21.4—16:

Cement-mortar Lining for Ductile-iron Pipe and Fittings

P2906.4

C110/A21.10—12:

Ductile-iron and Gray-iron Fittings

Table P2906.6, P3002.3

C115/A21.15—11:

Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

Table P2906.4

C151/A21.51—17:

Ductile-iron Pipe, Centrifugally Cast, for Water

Table P2906.4

C153/A21.53—11:

Ductile-iron Compact Fittings for Water Service

Table P2906.6

C500—09:

Standard for Metal-seated Gate Valves for Water Supply Service

Table P2903.9.4

C504—15:

Standard for Rubber-seated Butterfly Valves

Table P2903.9.4

C507—15:

Standard for Ball Valves, 6 In. Through 60 In. (150 mm through 1,500 mm)

Table P2903.9.4

C510—07:

Double Check Valve Backflow Prevention Assembly

Table P2902.3, P2902.3.6

C511—17:

Reduced-pressure Principle Backflow Prevention Assembly

Table P2902.3, P2902.3.5, P2902.5.1

C901—16:

Polyethylene (PE) Pressure Pipe and Tubing ¹/₂ in. (13 mm) through 3 in. (76 mm) for Water Service

P2906.4

C903—16:

Polyethylene-aluminum-polyethylene (PE-AL-PE) Composite Pressure Pipe, 12 mm (¹/₂ in.) through 50 mm (2 in.), for Water Service

Table M2105.4

C904—16:

Cross-linked Polyethylene (PEX) Pressure Tubing, ¹/₂ in. (13 mm) through 3 in. (76 mm) for Water Service

P2906.4

EN 15250—2007:

Slow Heat Release Appliances Fired by Solid Fuel Requirements and Test Methods

R1002.2

301—18:

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, Table P3302.1

310—18:

Specification for Coupling for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

P3003.4.3

ANSI A135.4—2012:

Basic Hardboard

Table R602.3(2)

ANSI A135.5—2012:

Prefinished Hardboard Paneling

R702.5

ANSI A135.6—2012:

Engineered Wood Siding

R703.5

ANSI A135.7—2012:

Engineered Wood Trim

R703.5

ANSI A208.1—2016:

Particleboard

R503.3.1, R602.1.9, R605.1

16 CFR, Part 1201—(2002):

Safety Standard for Architectural Glazing

R308.1.1, R308.3.1, Table R308.3.1(1)

16 CFR, Part 1209—(2002):

Interim Safety Standard for Cellulose Insulation

R302.10.3

16 CFR, Part 1404—(2002):

Cellulose Insulation

R302.10.3

A112.18.6—2017/CSA B125.6—2017:

Flexible Water Connectors

P2906.7

A112.19.5—2017/CSA B45.15—2017:

Flush Valves and Spuds for Water-closets, Urinals and Tanks

Table P2701.1

A112.19.7—2012/CSA B45.10—2012(R2017):

Hydromassage Bathtub Systems

Table P2701.1

A257.2—14:

Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

Table P3002.2, P3003.13

A257.3—14:

Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

P3003.5, P3003.13

AAMA/WDMA/CSA 101/I.S.2/A440—17:

North American Fenestration Standard/Specification for Windows, Doors and Unit Skylights

R308.6.9, R609.3

ANSI/CSA FC I—2014:

Fuel Cell Technologies—Part 3-100; Stationary Fuel Cell Power Systems—Safety

M1903.1

ANSI/CSA/IGSHPA C448 Series—16:

Design and Installation of Ground Source Heat Pump Systems for Commercial and Residential Buildings

Table M2105.4, Table M2105.5

ASME A17.1/CSA B44—2019:

Safety Code for Elevators and Escalators

R321.1

ASME A112.3.4—2018/CSA B45.9—2018:

Macerating Toilet Systems and Related Components

Table P2701.1, P3007.5

ASME A112.4.2—2015/CSA B45.16—2015(2020):

Water-closet Personal Hygiene Device

P2722.5

ASME A112.18.1—2018/CSA B125.1—2018:

Plumbing Supply Fittings

Table P2701.1, P2708.4, P2708.5, P2722.1, P2722.3, P2902.2, Table P2903.9.4

ASME A112.18.2—2020/CSA B125.2—2020:

Plumbing Waste Fittings

Table P2701.1, P2702.2

ASME A112.19.1—2018/CSA B45.2—18:

Enameled Cast-iron and Enameled Steel Plumbing Fixtures

Table P2701.1, P2711.1

ASME A112.19.2—2018/CSA B45.1—18:

Ceramic Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1, P2712.2, P2712.9

ASME A112.19.3—2017/CSA B45.4—2017:

Stainless Steel Plumbing Fixtures

Table P2701.1, P2705.1, P2711.1, P2712.1

ASSE 1002—2020/ASME A112.1002—2020/CSA B125.12—20:

Anti-Siphon Fill Valves for Water Closet Tanks

Table P2701.1, Table P2902.3, P2902.4.1

ASSE 1016—2017/ASME 112.1016—2017/CSA B125.16—2017:

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table P2701.1, P2708.4, P2722.2

ASSE 1070—2020/ASME A112.1070—2020/CSA B125.70—2020:

Performance Requirements for Water-temperature-limiting Devices

P2713.3, P2721.2, P2724.1

B44—2019:

Safety Code for Elevators and Escalators

R321.1

B64.1.1—11(R2016):

Vacuum Breakers, Atmospheric Type (AVB)

Table P2902.3, P2902.3.2

B64.1.2—11(R2016):

Pressure Vacuum Breakers (PVB)

Table P2902.3, P2902.3.4

B64.1.3—11(R2016):

Spill Resistant Pressure Vacuum Breakers (SRPVB)

Table P2902.3

B64.2—11(R2016):

Vacuum Breakers, Hose Connection Type (HCVB)

Table P2902.3, P2902.3.2

B64.2.1—11(R2016):

Hose Connection Vacuum Breakers (HCVB) with Manual Draining Feature

Table P2902.3, P2902.3.2

B64.2.1.1—11(2016):

Hose Connection Dual Check Vacuum Breakers (HCDVB)

Table P2902.3, P2902.3.2

B64.2.2—11(2016):

Vacuum Breakers, Hose Connection Type (HCVB) with Automatic Draining Feature

Table P2902.3, P2902.3.2

B64.3—11(2016):

Dual Check Backflow Preventers with Atmospheric Port (DCAP)

Table P2902.3, P2902.3.2, P2902.5.1

B64.4—11(2016):

Backflow Preventers, Reduced Pressure Principle Type (RP)

Table P2902.3, P2902.3.5

B64.4.1—11(2016):

Reduced Pressure Principle for Fire Sprinklers (RPF)

Table P2902.3, P2902.3.5

B64.5—11(2016):

Double Check Backflow Preventers (DCVA)

Table P2902.3, P2902.3.6

B64.5.1—11(2016):

Double Check Valve Backflow Preventers, Type for Fire Systems (DCVAF)

Table P2902.3, P2902.3.6

B64.6—11(2016):

Dual Check Valve Backflow Preventers (DuC)

Table P2902.3, P2902.3.7

B64.7—11(2016):

Laboratory Faucet Vacuum Breakers (LFVB)

Table P2902.3, P2902.3.2

B125.3—18:

Plumbing Fittings

Table P2701.1, P2713.3, P2721.2, Table P2902.3, P2902.4.1, Table P2903.9.4

B137.1—17:

Polyethylene (PE) Pipe, Tubing and Fittings for Cold Water Pressure Services

Table P2906.4, Table P2906.6

B137.2—17:

Polyvinylchloride PVC Injection-moulded Gasketed Fittings for Pressure Applications

Table P2906.6

B137.3—17:

Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

Table P2906.4, Table P2906.6, P3003.9.2

B137.5—17:

Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications

Table P2906.4, Table P2906.5, Table P2906.6

B137.6—17:

Chlorinated polyvinylchloride CPVC Pipe, Tubing and Fittings For Hot- and Cold-water Distribution Systems

Table P2906.4, Table P2906.5, Table 2906.6

B137.9—17:

Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe Systems

Table M2101.1, Table P2906.4

B137.10—17:

Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PE-AL-PE) Composite Pressure Pipe Systems

Table M2101.1, Table P2906.4, Table P2906.5, Table P2906.6, P2906.12.1

B137.11—17:

Polypropylene (PP-R) Pipe and Fittings for Pressure Applications

Table P2906.4, Table P2906.5, Table P2906.6

B137.18—17:

Polyethylene of Raised Temperature (PE-RT) Tubing Systems for Pressure Applications

Table M2101.1, Table M2105.4, Table M2105.5, Table P2906.4, Table P2906.5, Table P2906.6

B181.1—18:

Acrylonitrile-butadiene-styrene (ABS) Drain, Waste and Vent Pipe and Pipe Fittings

Table P3002.1(1), Table P3002.1(2), Table P3002.3, P3003.3.2

B181.2—18:

Polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) Drain, Waste and Vent Pipe and Pipe Fittings

Table P3002.1(1), Table P3002.1(2), P3003.9.2, P3008.3

B181.3—18:

Polyolefin and polyvinylidene (PVDF) Laboratory Drainage Systems

Table P3002.1(1), Table P3002.1(2), Table P3002.2, Table P3002.3, P3003.11.1

B182.1—18:

Plastic Drain and Sewer Pipe and Pipe Fittings

Table P3302.1

B182.2—18:

PSM Type polyvinylchloride (PVC) Sewer Pipe and Fittings

Table P3002.2, Table P3302.1

B182.4—18:

Profile polyvinylchloride (PVC) Sewer Pipe & Fittings

Table P3002.2, Table P3302.1

B182.6—18:

Profile Polyethylene (PE) Sewer Pipe and Fittings for leak-proof Sewer Applications

Table P3302.1

B182.8—18:

Profile Polyethylene (PE) Storm Sewer and Drainage Pipe and Fittings

Table P3302.1

B356—10(R2020):

Water Pressure Reducing Valves for Domestic Water Supply Systems

P2903.3.1

B483.1—07(R2017):

Drinking Water Treatment Systems

P2909.1, P2909.2

B602—16:

Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

P3003.3.1, P3003.4.3, P3003.5, P3003.9.1, P3003.10, P3003.12.2, P3003.13

C22.2 No. 218.1—13(R2017):

Spas, Hot Tubs and Associated Equipment

M2006.1

C22.2 No. 236—15:

Heating and Cooling Equipment

M2006.1

CSA/C22.2 No. 60335-2-40—2019:

Safety of Household and Similar Electrical Appliances, Part 2-40: Particular Requirements for Electrical Heat Pumps, Air-Conditioners and Dehumidifiers, 3rd edition

M1402.1, M1403.1, M1412.1, M1413.1, M2006.1

CSA 8—93:

Requirements for Gas Fired Log Lighters for Wood Burning Fireplaces

G2433.1

CSA A257.1—2014:

Non-reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

Table P3002.2

CSA B45.5—2017/IAPMO Z124—2017 with Errata dated August 2017:

Plastic Plumbing Fixtures

Table P2701.1, P2711.1, P2711.2, P2712.1

CSA B805—18/ICC 805—18:

Rainwater Harvesting Systems

P2912.1

CSA O325—16:

Construction Sheathing

R503.2.1, R602.1.8, R604.1, R803.2.1

O437-Series—93(R2011):

Standards on OSB and Waferboard

R503.2.1, R602.1.8, R604.1, R803.2.1

CSSB—97:

Grading and Packing Rules for Western Red Cedar Shakes and Western Red Cedar Shingles of the Cedar Shake and Shingle Bureau

R702.6, R703.6

ANSI/DASMA 108—2017:

Standard Method for Testing Sectional Doors, Rolling Doors and Flexible Doors: Determination of Structural Performance Under Uniform Static Air Pressure Difference

R609.4

ANSI/DASMA 115—2017:

Standard Method for Testing Sectional Garage Doors, Rolling Doors and Flexible Doors: Determination of Structural Performance Under Missile Impact and Cyclic Wind Pressure

R301.2.1.2

ANSI/HPVA HP-1—2016:

American National Standard for Hardwood and Decorative Plywood

R702.5

PS 1—19:

Structural Plywood

R404.2.1, Table R404.2.3, R503.2.1, R602.1.8, R604.1, R803.2.1

PS 2—18:

Performance Standard for Wood Structural Panels

R404.2.1, Table R404.2.3, R503.2.1, R602.1.8, R604.1, R803.2.1

PS 20—05:

American Softwood Lumber Standard

R404.2.1, R502.1.1, R602.1.1, R802.1.1

49 CFR, Parts 192.281(e) & 192.283 (b) (2009):

Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards

G2414.5.1

FEMA TB-2—08:

Flood Damage-resistant Materials Requirements

R322.1.8

FEMA TB-11—01:

Crawlspace Construction for Buildings Located in Special Flood Hazard Area

R408.7

4450—(1989):

Approval Standard for Class 1 Insulated Steel Deck Roofs—with Supplements through July 1992

R906.1

4474—2011:

American National Standard for Evaluating the Simulated Wind Uplift Resistance of Roof Assemblies Using Static Positive and/or Negative Differential Pressures

R905.4.4.1

ANSI/FM 4880—(2017):

American National Standard for Evaluating the Fire Performance of Insulated Building Panel Assemblies and Interior Finish Materials

R316.6

GA-253—2018:

Application of Gypsum Sheathing

Table R602.3(1)

CSA B45.5—17/IAPMO Z124—2017:

Plastic Plumbing Fixtures

Table P2701.1, P2711.1, P2711.2, P2712.1

ICC 400—17:

Standard on the Design and Construction of Log Structures

R301.1.1, R502.1.4, R602.1.4, R703.1, R802.1.3

ICC 500—2020:

ICC/NSSA Standard for the Design and Construction of Storm Shelters

R323.1

ICC 600—2020:

Standard for Residential Construction in High-wind Regions

R301.2.1.1

ICC 900/SRCC 300—2020:

Solar Thermal System Standard

M2301.2.2.2, M2301.2.3, M2301.2.6, M2301.2.7, M2301.2.8, M2301.2.10, M2301.4

ICC 901/SRCC 100—2020:

Solar Thermal Collector Standard

M2301.3.1

ICC/ANSI A117.1—17:

Accessible and Usable Buildings and Facilities

R321.3

IEBC—21:

International Existing Building Code^®

R110.2

IPMC—21:

International Property Maintenance Code^®

R102.7

IPSDC—21:

International Private Sewage Disposal Code^®

R322.1.7

ISPSC—21:

International Swimming Pool and Spa Code^®

R327.1

SCBC—21:

South Carolina Building Code

R320.1.1, R101.2, R202, R301.1.1, R301.1.3, R301.2.1.1, R301.2.2.1.1, R301.2.2.1.2, R301.3, Table R302.1(1), Table R302.1(2), R302.2.1, R302.2.2, R302.3, R308.5, R320.1, R321.3, R403.1.8, Table R602.10.3(3), Table R606.12.2.1, R609.2, R802.1.5.4, R905.10.3, G2402.3

SCFC—21:

South Carolina Fire Code

R102.7, R324.2, M2201.7, G2402.3, G2412.2

SCFGC—21:

South Carolina Fuel Gas Code

G2401.1, G2402.3, G2423.1

SCMC—21:

South Carolina Mechanical Code

G2402.3

SCPC—21:

South Carolina Plumbing Code

Table R301.2, R903.4.1, G2402.3, P2601.1

8336—2009:

Fibre-cement Flat Sheets-product Specification and Test Methods

Table R503.2.1.1(1), Table R503.2.1.1(2), Table R602.3(2), Table R702.4.2, R703.10.1, R703.10.2

15874—2002:

Polypropylene Plastic Piping Systems for Hot and Cold Water Installations

Table M2101.1

SP-42—2013:

Corrosion Resistant Gate, Globe, Angle and Check Valves with Flanged and Butt Weld Ends (Classes 150, 300 & 600)

Table P2903.9.4

SP-58—2009:

Pipe Hangers and Supports—Materials, Design, Manufacture, Selection, Application and Installation

G2418.2

SP-67—2011:

Butterfly Valves

Table P2903.9.4

SP-70—2011:

Gray Iron Gate Valves, Flanged and Threaded Ends

Table P2903.9.4

SP-71—2011:

Gray Iron Swing Check Valves, Flanged and Threaded Ends

Table P2903.9.4

SP-72—2010a:

Ball Valves with Flanged or Butt-Welding Ends for General Service

P2903.9.4

SP-78—2011:

Cast Iron Plug Valves, Flanged and Threaded Ends

Table P2903.9.4

SP-80—2019:

Bronze Gate, Globe, Angle and Check Valves

Table P2903.9.4

SP-110—2010:

Ball Valves, Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends (incl. a 2010 Errata Sheet)

Table P2903.9.4

SP-122—2012:

Plastic Industrial Ball Valves

Table P2903.9.4

SP-139—2014:

Copper Alloy Gate, Globe, Angle, and Check Valves for Low Pressure/ Low Temperature Plumbing Applications

Table P2903.9.4

AH 116—09:

Fibrous Glass Duct Construction Standards, Fifth Edition

M1601.1.1

13D—19:

Standard for the Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes

R313.1.1, R313.2.1, R324.6.2.1, P2904.1, P2904.6.1

13R—19:

Standard for the Installation of Sprinkler Systems in Low-Rise Residential Occupancies

R325.5

31—20:

Standard for the Installation of Oil-burning Equipment

M1701.1, M1801.3.1, M1805.3, M2201.2

58—20:

Liquefied Petroleum Gas Code

G2412.2, G2414.5.2

70—20:

National Electrical Code

R107.3, R324.3, R328.6, E3401.1, E3401.2, E4301.1, Table E4303.2, E4304.3, E4304.4

72—19:

National Fire Alarm and Signaling Code

R314.1, R314.7.1

85—19:

Boiler and Combustion Systems Hazards Code

G2452.1

211—19:

Standard for Chimneys, Fireplaces, Vents and Solid Fuel-Burning Appliances

R1002.5, G2427.5.5.1

259—18:

Standard Test Method for Potential Heat of Building Materials

R316.5.7, R316.5.8

275—17:

Standard Method of Fire Tests for the Evaluation of Thermal Barriers

R316.4

276—19:

Standard Method of Fire Test for Determining the Heat Release Rate of Roofing Assemblies with Combustible Above-deck Roofing Components

R906.1

286—19:

Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth

R302.9.4, R316.6

501—17:

Standard on Manufactured Housing

R202

720—15:

Standard for the Installation of Carbon Monoxide (CO) Detectors and Warning Equipment

R315.7.1, R315.7.2

853—20:

Standard for the Installation of Stationary Fuel Cell Power Systems

M1903.1

ANSI/NGWA 01—14:

Water Well Construction Standard

P2602.1

14—2017:

Plastics Piping System Components and Related Materials

M1301.4, P2609.3, P2909.3

41—2016:

Non-Liquid Saturated Treatment Systems

P2725.1

42—2017:

Drinking Water Treatment Units—Aesthetic Effects

P2909.1, P2909.3

44—2017:

Residential Cation Exchange Water Softeners

P2909.1, P2909.3

50—2017:

Equipment for Swimming Pools, Spas, Hot Tubs and Other Recreational Water Facilities

P2911.8.1

53—2017:

Drinking Water Treatment Units—Health Effects

P2909.1, P2909.3

58—2017:

Reverse Osmosis Drinking Water Treatment Systems

P2909.2, P2909.3

61—2018:

Drinking Water System Components—Health Effects

P2609.5, P2722.1, P2903.9.4, P2906.4, P2906.5, P2906.6, P2909.3

62—2017:

Drinking Water Distillation Systems

P2909.1

350—2017a:

Onsite Residential and Commercial Water Reuse Treatment Systems

P2911.6.1

358-1—2017:

Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems

M2105.4, M2105.5

358-2—2017:

Polypropylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems

Table M2105.4, M2105.5

358-3—2016:

Cross-linked Polyethylene (PEX) Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems

Table M2105.4, Table M2105.5

358-4—2018:

Polyethylene of Raised Temperature (PE-RT) Tubing and Fittings for Water-Based Ground-Source (Geothermal) Heat Pump Systems

Table 2105.4, Table 2105.5

359—2016:

Valves for Crosslinked Polyethylene (PEX) Water Distribution Tubing Systems

Table P2903.9.4

372—2016:

Drinking Water Systems Components—Lead Content

P2906.2.1

100—17:

Prescriptive Design of Exterior Concrete Walls for One- and Two-family Dwellings (Pub. No. PCA 100.3)

R301.2.2.5, R404.1.3, R404.1.3.2.1, R404.1.3.2.2, R404.1.3.4, R404.1.4.2, R608.1, R608.2, R608.5.1, R608.9.2, R608.9.3

ANSI/SBCA FS100—2012(R2018):

Standard Requirements for Wind Pressure Resistance of Foam Plastic Insulating Sheathing Used in Exterior Wall Covering Assemblies

R316.8

BCSI—2018:

Building Component Safety Information Guide to Good Practice for Handling, Installing, Restraining & Bracing of Metal Plate Connected Wood Trusses

R502.11.2, R802.10.3

CFS-BCSI—(updated June 2016):

Cold-formed Steel Building Component Safety Information (CFSBCSI) Guide to Good Practice for Handling, Installing & Bracing of Cold-formed Steel Trusses

R505.1.3, R804.3.6

SMACNA—2010:

Fibrous Glass Duct Construction Standards 7th edition

M1601.1.1, M1601.4.1

ANSI/SMACNA 006—2020:

HVAC Duct Construction Standards—Metal and Flexible 4th Edition

M1601.4.1

402—2016:

Building Code Requirements for Masonry Structures

R404.1.2, R606.1, R606.1.1, R606.12.1, R606.12.2.3.1, R606.12.3.1, R703.12

403—2017:

Direct Design Handbook for Masonry Structures

R606.1, R606.1.1, R606.12.1, R606.12.3.1

404—2016:

Standard for the Design of Architectural Cast Stone

R606.1

602—2016:

Specification for Masonry Structures

R606.2.10, R606.2.13, R703.12

TPI 1—2014:

National Design Standard for Metal Plate Connected Wood Truss Construction

R502.11.1, R802.10.2

17—2008:

Vent or Chimney Connector Dampers for Oil-fired Appliances—with revisions through September 2013

M1802.2.2

55A—2004:

Materials for Built-up Roof Coverings

R905.9.2

58—2018:

Steel Underground Tanks for Flammable and Combustible Liquids

M2201.1

80—2007:

Steel Tanks for Oil-burner Fuel—with revisions through January 2014

M2201.1

103—2010:

Factory-built Chimneys for Residential Type and Building Heating Appliances—with revisions through March 2017

R202, R1005.3, G2430.1

127—2011:

Factory-built Fireplaces—with revisions through July 2016

R1001.11, R1004.1, R1004.4, R1004.5, R1005.4, G2445.7

174—2004:

Household Electric Storage Tank Water Heaters—with revisions through December 2016

M2005.1

180—2012:

Liquid-level Indicating Gauges for Oil Burner Fuels and Other Combustible Liquids—with revisions through May 2017

M2201.5

181—2005:

Factory-made Air Ducts and Air Connectors—with revisions through April 2017

M1601.1.1, M1601.4.1

181A—2013:

Closure Systems for Use with Rigid Air Ducts and Air Connectors—with revisions through March 2017

M1601.2, M1601.4.1

181B—2013:

Closure Systems for Use with Flexible Air Ducts and Air Connectors—with revisions through March 2017

M1601.4.1

217—2015:

Smoke Alarms—with revisions through November 2016

R314.1.1, R315.1.1

263—2011:

Fire Test of Building Construction and Materials—with revisions through March 2018

Table R302.1(2), R302.2, R302.2.1, R302.2.2, R302.4.1, R302.11.1, R606.2.2

268—2016:

Smoke Detectors for Fire Alarm Systems—with revisions through July 2016

R314.7.1, R314.7.4, R315.7.4

325—2017:

Door, Drapery, Gate, Louver and Window Operations and Systems

R309.4

343—2017:

Pumps for Oil-burning Appliances

M2204.1

378—06:

Draft Equipment—with revisions through September 2013

M1804.2.6, G2427.3.3

441—16:

Gas Vents—with revisions through July 2016

G2426.1, G2427.6.1

467—13:

Grounding and Bonding Equipment

G2411.2.5

507—2017:

Electric Fans—with revisions through August 2018

M1503.2

508—2018:

Industrial Control Equipment

M1411.3.1

536—2014:

Flexible Metallic Hose

M2202.3

580—2006:

Test for Uplift Resistance of Roof Assemblies—with Revisions through October 2013

R905.4.4.1

641—2010:

Type L, Low-temperature Venting Systems—with revisions through April 2018

R202, R1003.11.5, M1804.2.4, G2426.1, G2427.6.1

651—2011:

Schedule 40, Type EB and A Rigid PVC Conduit and Fittings—with revisions through June 2016

G2414.5.3

705—2017:

Power Ventilators—with revisions through October 2018

M1502.4.4

723—2018:

Standard for Test for Surface Burning Characteristics of Building Materials

R202, R302.9.3, R302.9.4, R302.10.1, R302.10.2, R316.3, R316.5.9, R316.5.11, R507.2.2.2, R703.14.3, R802.1.5, M1601.3, M1601.5.2, P2801.6

726—95:

Oil-fired Boiler Assemblies—with revisions through October 2013

M2001.1.1, M2006.1

727—2018:

Oil-fired Central Furnaces

M1402.1

729—2003:

Oil-fired Floor Furnaces

M1408.1

730—03:

Oil-fired Wall Furnaces—with revisions through November 2016

M1409.1

732—2018:

Oil-fired Storage Tank Water Heaters—with revisions through August 2018

M2005.1

737—2011:

Fireplaces Stoves

M1414.1, M1901.2

790—04:

Standard Test Methods for Fire Tests of Roof Coverings—with revisions through October 2018

R302.2.4, R902.1

795—2016:

Commercial-industrial Gas Heating Equipment

G2442.1, G2452.1

834—2004:

Heating, Water Supply and Power Boilers—Electric—with revisions through September 2018

M2001.1.1

842—2015:

Valves for Flammable Fluids—with revisions through May 2015

M2204.2

858—2014:

Household Electric Ranges—with revisions through June 2018

M1503.2, M1901.2

875—09:

Electric Dry-bath Heaters—with revisions through September 2017

M1902.2

896—1993:

Oil-burning Stoves—with revisions through November 2016

M1410.1

907—94:

Fireplace Accessories—with revisions through November 2014

R1001.13

923—2013:

Microwave Cooking Appliances—with revisions through July 2017

M1503.2, M1504.1, M1901.2

959—2010:

Medium Heat Appliance Factory-built Chimneys—with revisions through June 2014

R1005.6

1026—2012:

Electric Household Cooking and Food Serving Appliances—with revisions through July 2018

M1901.2

1040—1996:

Fire Test of Insulated Wall Construction—with revisions through April 2017

R316.6

1042—2009:

Electric Baseboard Heating Equipment—with revisions through December 2016

M1405.1

1256—02:

Fire Test of Roof Deck Construction—with revisions through August 2018

R906.1

1261—2016:

Electric Water Heaters for Pools and Tubs—with revisions through September 2017

M2006.1

1479—2015:

Fire Tests of Through-Penetration Firestops

R302.4.1.2

1482—2011:

Solid-Fuel-type Room Heaters—with revisions through August 2015

R1002.2, R1002.5, M1410.1

1563—2009:

Electric Spas, Equipment Assemblies, and Associated Equipment—with revisions through October 2017

M2006.1

1618—2015:

Wall Protectors, Floor Protectors, and Hearth Extensions—with revisions through January 2018

R1004.2, M1410.2

1693—2010:

Electric Radiant Heating Panels and Heating Panel Sets—with revisions through October 2011

M1406.1

1703—2002:

Flat-plate Photovoltaic Modules and Panels—with revisions through September 2018

R324.3.1, R902.4, R905.16.4

1715—97:

Fire Test of Interior Finish Material—with revisions through April 2017

R316.6

1738—2010:

Venting Systems for Gas-burning Appliances, Categories II, III and IV

G2426.1, G2427.4.1, G2427.4.1.1, G2427.4.2

1741—2010:

Inverters, Converters, Controllers and Interconnection System Equipment with Distributed Energy Resources—with revisions through February 2018

R324.3.1, R328.6

1777—07:

Chimney Liners—with revisions through April 2014

R1003.11.1, R1003.18, M1801.3.4, G2425.12, G2425.15.4, G2427.5.1, G2427.5.2

1897—15:

Uplift Tests for Roof Covering Systems

R905.4.4.1

1995—2015:

Heating and Cooling Equipment—with revisions through August 2018

M1402.1, M1403.1, M1407.1, M1412.1, M1413.1, M2006.1

1996—2009:

Electric Duct Heaters—with revisions through July 2016

M1402.1, M1407.1

2034—2017:

Standard for Single- and Multiple-station Carbon Monoxide Alarms—with revisions through September 2018

R314.1.1, R315.1.1

2075—2013:

Gas and Vapor Detectors and Sensors—with revisions through December 2017

R314.7.4, R315.7.1, R315.7.4

2158A—2013:

Outline of Investigation for Clothes Dryer Transition Duct—with revisions through April 2017

M1502.4.3, G2439.7.3

2200—2012:

Stationary Engine Generator Assemblies—with revisions through October 2015

R329.1

2523—2009:

Standard for Solid Fuel-fired Hydronic Heating Appliances, Water Heaters and Boilers—with revisions through March 2018

M2001.1.1, M2005.1

2703—2014:

Mounting Systems, Mounting Devices, Clamping/Retention Devices and Ground Lugs for Use with Flat-Plate Photovoltaic Modules and Panels—with revisions through December 2019

R902.4

7103—19:

Outline of Investigation for Building-Integrated Photovoltaic Roof Covering

R902.3, R905.16.4, Table 905.16.6, R905.17.5

9540—2016:

Standard for Energy Storage Systems and Equipment

R328.2, R328.6

61730-1—2017:

Photovoltaic (PV) Module Safety Qualification—Part 1: Requirements for Construction

R324.3.1 , R905.16.4 , 905.17.5

61730-2—2017:

Photovoltaic (PV) Module Safety Qualification—Part 2: Requirements for Testing

R324.3.1, R905.16.4, R905.17.5

UL/CSA/60335-2-40—2019:

Standard for Household and Similar Electrical Appliances, Part 2-40: Particular Requirements for Electrical Heat Pumps, Air-conditioners and Dehumidifiers

M1402.1, M1403.1, M1412.1, M1413.1, M2006.1

CAN/ULC S 102.2—2018:

Standard Method of Test for Surface Burning Characteristics of Building Materials and Assemblies

R302.10.1, R302.10.2

AAMA/WDMA/CSA 101/I.S.2/A440—17:

North American Fenestration Standard/Specification for Windows, Doors and Skylights

R308.6.9, R609.3

I.S. 11—18:

Industry Standard Analytical Method for Design Pressure (DP) Ratings of Fenestration Products

R308.6.9.1, R609.3.1

ANSI WMA 100—2018:

Standard Method of Determining Structural Performance Ratings of Side-Hinged Exterior Door Systems and Procedures for Component Substitution

R609.3