Chapter 15 Referenced Standards

North American Standard for Cold-Formed Steel Nonstructural Framing

307.3

North American Standard for Cold-Formed Steel Structural Framing, 2020

307.3

Standard Specifications for Load-bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation

421.5.2.5, 421.5.2.6

Relief Valves for Hot Water Supply Systems

504.2, 504.4, 504.4.1

Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water Connection Receptors)

406.1, 409.2, Table 608.1, 608.14.1

Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances

406.1, 409.2, Table 608.1, 608.14.1, 1102.6

Stainless Steel Drainage Systems for Sanitary, DWV, Storm and Vacuum Applications Above and Below Ground

413.1, Table 702.1, Table 702.2, Table 702.3, Table 702.4, Table 1102.4, Table 1102.5, 1102.6, Table 1102.7

Water Heater Relief Valve Drain Tubes

504.6

Water Closet Personal Hygiene Devices

412.9

Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System

405.4

Plastic Push-Fit Drain, Waste, and Vent (DWV) Fittings

705.2.5

Manually or Automatically Operated Valves for Use in Plumbing Systems

Table 605.7

Floor Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use

405.4.3

Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks

405.4.3

Floor and Trench Drains

413.1

Roof, Deck, and Balcony Drains

1102.6

Sanitary Floor Sinks

414.1

Siphonic Roof Drains

1107.1

Backwater Valves

714.2

Grease Interceptors

1003.3.5

Grease Removal Devices

1003.3.5

FOG (Fats, Oils and Greases) Disposal Systems

1003.3, 1003.3.5, 1003.3.7

Plumbing Supply Fittings

412.1, 412.2, 412.3, 412.4, 412.6, 412.8, Table 605.7, 607.4, 608.2

Plumbing Waste Fittings

412.1.2, 421.3.1

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

412.2, 412.6

Flexible Water Connectors

605.6

Protectors/Insulators for Exposed Waste and Supplies on Accessible Fixtures

404.3

Enameled Cast Iron and Enameled Steel Plumbing Fixtures

407.1, 410.1, 418.1, 419.1, 421.1, 422.1

Ceramic Plumbing Fixtures

401.2, 405.10, 407.1, 408.1, 410.1, 418.1, 419.1, 421.1, 422.1, 424.1, 425.1

Stainless Steel Plumbing Fixtures

405.9, 407.1, 408.1, 410.1, 418.1, 419.1, 421.1, 425.1

Flush Valves and Spuds for Water Closets, Urinals, and Tanks

415.4

Hydromassage Bathtub Systems

426.1, 426.4

Wall Mounted and Pedestal Mounted, Adjustable, Elevating, Tilting and Pivoting Lavatory, Sink and Shampoo Bowl Carrier Systems and Drain Waste Systems

419.4

Six-liter Water Closets Equipped with a Dual Flushing Device

425.1

Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors

407.4, 426.6

Vitreous China Nonwater Urinals

424.1

Hydrants for Utility and Maintenance Use

Table 608.1, 608.14.6

Cleanouts

708.1.11.2

Macerating Toilet Systems and Waste Pumping Systems for Plumbing Fixtures

405.5, 712.4.1

Anti-Siphon Fill Valves for Water Closet Tanks

415.3.1, Table 608.1

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

412.3, 412.4, 607.4

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

415.2

Performance Requirements for Water Temperature Limiting Devices

408.3, 412.5, 412.10, 419.5, 423.3, 607.1.2

Pipe Threads, General Purpose (inch)

605.10.3, 605.12.4, 605.14.3, 605.17.1, 705.2.3, 705.5.4, 705.8.1, 705.10.3

Malleable Iron Threaded Fittings Classes 150 and 300

Table 1102.7

Gray Iron Threaded Fittings Classes 125 and 250

Table 605.5, Table 702.4, Table 1102.7

Factory-Made Wrought Steel Buttwelding Fittings

Table 605.5, Table 702.4, Table 1102.7

Forged Fittings, Socket-Welding and Threaded

Table 605.5, Table 702.4, Table 1102.7

Cast Iron Threaded Drainage Fittings

Table 702.4, Table 1102.7

Cast Alloy Threaded Fittings: Classes 125 and 250

Table 605.5, Table 702.4, Table 1102.7

Cast Copper Alloy Solder Joint Pressure Fittings

Table 605.5, Table 702.4, Table 1102.7

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

Table 605.5, Table 702.4, Table 1102.7

Cast Copper Alloy Solder Joint Drainage Fittings DWV

Table 702.4, Table 1102.7

Cast Copper Alloy Fittings for Flared Copper Tubes

Table 605.5, Table 702.4, Table 1102.7

Wrought Steel Buttwelding Short Radius Elbows and Returns

Table 605.5, Table 702.4, Table 1102.7

Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings (DWV)

Table 702.4, Table 1102.7

Valves—Flanged, Threaded and Welding End

Table 605.7

Copper and Copper Alloy Press-Connect Pressure Fittings

Table 605.5

Siphonic Roof Drainage

1107.1

Test Method for Evaluating Roof Drain Performance

1102.6

Performance Requirements for Atmospheric Type Vacuum Breakers

415.2, Table 608.1, 608.14.6, 608.17.4.1

Performance Requirements for Commercial Dishwashing Machines

409.1

Performance Requirements for Water Heater Drain Valves 3/4 Inch Size

501.3

Performance Requirements for Plumbing Aspects of Residential Food Waste Disposer Units

413.1

Performance Requirements for Water Hammer Arresters

604.9

Performance Requirements for Hose Connection Vacuum Breakers

Table 608.1, 608.14.6

Performance Requirements for Backflow Preventers with an Intermediate Atmospheric Vent

Table 608.1, 608.14.3, 608.17.2, 608.17.10

Performance Requirements for Reduced Pressure Principle Backflow Prevention Assemblies

Table 608.1, 608.14.2, 608.17.2

Performance Requirements for Backflow Prevention Devices for Hand-held Showers

412.2

Performance Requirements for Double Check Backflow Prevention Assemblies

607.1.2, Table 608.1, 608.14.7

Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems

501.2, 613.1

Performance Requirements for Trap Seal Primer Valves; Potable Water Supplied

1002.4.1.2

Performance Requirements for Wall Hydrant with Backflow Protection and Freeze Resistance

Table 608.1, 608.14.6

Performance Requirements for Pressure Vacuum Breaker Assembly

Table 608.1, 608.14.5

Performance Requirements for Backflow Preventer for Beverage Dispensing Equipment

Table 608.1, 608.17.1.1, 608.17.1.2

Performance Requirements for Electrically Heated or Cooled Water Dispensers

412.12

Performance Requirements for Dual Check Backflow Preventers

605.3.1, Table 608.1, 608.14.9, 608.17.1.2

Dual Check Valve Type Backflow Preventers for Carbonated Beverage Dispensers—Post Mix Type

608.17.1.2

Performance Requirements for Laboratory Faucet Backflow Preventers

Table 608.1, 608.14.6

Performance Requirements for Trap Seal Primer—Drainage Types and Electronic Design Types

1002.4.1.3

Performance Requirements for Reduced Pressure Detector Backflow Prevention Assemblies

Table 608.1, 608.14.2

Performance Requirements for Double Check Detector Backflow Prevention Assemblies

Table 608.1, 608.14.7

Performance Requirements for Individual and Branch Type Air Admittance Valves for Chemical Waste Systems

901.3, 918.8

Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems

918.1

Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems

918.1

Performance Requirements for Hose Connection Backflow Preventers

Table 608.1, 608.14.6

Performance Requirements for Spill Resistant Vacuum Breaker Assemblies

Table 608.1, 608.14.5

Performance Requirements for Outdoor Enclosures for Fluid Conveying Components

608.15.1

Performance Requirements for Push-Fit Fittings

Table 605.5, 605.14.4, 605.16.3

Performance Requirements for Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings

412.7

Performance Requirements for Backflow Prevention Assembly Field Test Kits

312.11.2

Performance Requirements for Individual Pressure Balancing In-line Valves for Individual Fixture Fittings

604.11

Performance Requirements for Automatic Temperature Control Mixing Valves

412.4

Performance Requirements for Temperature Actuated Mixing Valves for Plumbed Emergency Equipment

411.3, 412.5, 412.10, 419.5, 423.3, 607.1.2

Performance Requirements for Trap Seal Protection for Floor Drains

1002.4.1.4

Performance Requirements for Dielectric Pipe Unions

605.23.1, 605.23.3

Performance Requirements for Backflow Preventers with Integral Pressure Reducing Boiler Feed Valve and Intermediate Atmospheric Vent Style for Domestic and Light Commercial Water Distribution Systems

608.14.3, 608.17.2

Performance Requirements for Water Heaters with Integral Temperature Control Devices for Hot Water Distribution Systems.

412.10, 607.1.1

Performance Requirements for Water Heaters with Temperature Limiting Capacity

412.5, 607.1.2

Performance Requirements for Water Heaters for Emergency Equipment

411.3, 607.1.1, 607.1.2

Performance Requirements for Reduced Pressure Principle Backflow Preventers (RPA) and Reduced Pressure Principle Fire Protection Backflow Preventers (RFP)

312.11.2

Performance Requirements for Testing Double Check Valve Backflow Prevention Assemblies (DC) and Double Check Fire Protection Backflow Prevention Assemblies (DCF)

312.11.2

Performance Requirements for Testing Pressure Vacuum Breaker Assemblies (PVB)

312.11.2

Performance Requirements for Testing Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies (RPDF)

312.11.2

Performance Requirements for Testing Double Check Detector Fire Protection Backflow Prevention Assemblies (DCDF)

312.11.2

Performance Requirements for Testing Hose Connection Backflow Preventers

312.11.2

Performance Requirements for Testing Spill Resistant Vacuum Breaker (SRVB)

312.11.2

Anti-Siphon Fill Valves for Water Closet Tanks

415.3.1, Table 608.1

Performance Requirements for Water-pressure-reducing Valves for Domestic Water Distribution Systems

604.8

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

412.3, 412.4, 607.4

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

415.2

Performance Requirements for Water Temperature Limiting Devices

408.3, 412.5, 412.10, 419.5, 423.3, 607.1.2

Performance Requirements for Chemical Dispensing Systems with Integral Backflow Protection

608.14.8

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

Table 605.3, Table 605.4, Table 702.1

Specification for Cast Iron Soil Pipe and Fittings

Table 702.1, Table 702.2, Table 702.3, Table 702.4, 708.1.6, Table 1102.4, Table 1102.5, Table 1102.7

Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service

Table 605.3

Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

Table 605.3, Table 605.4, Table 605.5, 605.22.2

Standard Specification for Corrosion-Resistant High-Silicon Iron Castings

Table 702.6

Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples

Table 605.8

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

Table 605.3, Table 605.4, Table 605.5

Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application

Table 702.1, Table 702.2, Table 702.3, Table 702.4, Table 1102.4, Table 1102.5, Table 1102.7

Specification for Solder Metal

605.12.3, 605.13.6, 705.5.3, 705.6.1

Specification for Seamless Copper Pipe, Standard Sizes

Table 605.3, Table 605.4, Table 702.1

Specification for Seamless Red Brass Pipe, Standard Sizes

Table 605.4, Table 702.1

Specification for Seamless Copper Tube

Table 605.3, Table 605.4, Table 702.1, Table 702.2, Table 702.3, Table 1102.4

Standard Specification for Seamless Copper Water Tube

Table 605.3, Table 605.4, Table 702.1, Table 702.2, Table 702.3, Table 1102.4

Standard Specification for Copper Sheet, Strip Plate,  and Rolled Bar

402.3, 415.3.3, 902.2

Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube

Table 605.3, Table 605.4, Table 702.1, Table 702.2, Table 702.3, Table 1102.4

Specification for Threadless Copper Pipe, Standard Sizes

Table 605.3, Table 605.4, Table 702.1

Specification for Copper Drainage Tube (DWV)

Table 702.1, Table 702.2, Table 1102.4

Specification for Welded Copper Tube

Table 605.3, Table 605.4

Specification for Brass, Copper and Chromium-plated Pipe Nipples

Table 605.8

Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube

605.12.3, 605.13.6, 705.5.3, 705.6.1

Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

605.12.3, 605.13.6, 705.5.3, 705.6.1

Specification for Clay Drain Tile and Perforated Clay Drain Tile

Table 702.3, Table 1102.4, Table 1102.5

Specification for Nonreinforced Concrete Sewer, Storm Drain and Culvert Pipe

Table 702.3, Table 1102.4

Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

Table 702.3, Table 1102.4

Specification for Compression Joints for Vitrified Clay Pipe and Fittings

705.11, 705.16

Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

705.4, 705.16

Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

705.3.2, 705.3.3, 705.16

Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

Table 702.3, Table 702.4, Table 1102.4, Table 1102.5

Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications

Table 702.1, Table 702.4

Specification for Flexible Transition Couplings for Underground Piping System

705.2.1, 705.5, 705.10.1, 705.11, 705.12.2, 705.16

Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

705.3.3

Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

705.16

Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

705.16

Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

705.19

Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-Iron Soil Pipe and Fittings

705.3.3

Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent and Storm Piping Applications

705.3.2

Standard Specification for Insulating Covers on Accessible Lavatory Piping

404.3

Standard Test Method For Residual Chlorine in Water

1301.2.1, 1303.9

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

Table 605.3

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

Table 605.3

Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

605.10.2, 705.2.2

Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Table 605.3

Standard Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)

Table 605.3

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

Table 605.3

Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

Table 605.5, 605.21.3

Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

Table 605.5

Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

Table 605.5

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40

Table 605.5

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

605.21.3, 705.10.2, 705.14.2

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

Table 605.5

Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

605.18.2, 705.12.1

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

Table 702.1, Table 702.2, Table 702.3, Table 702.4, 705.2.2, Table 1102.4, Table 1102.7

Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

Table 702.1, Table 702.2, Table 702.3, Table 702.4, Table 1102.4, Table 1102.7

Specification for Joints for IPS PVC Pipe Using Solvent Cement

Table 605.3

Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping

Table 702.3

Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

Table 605.5, Table 702.4, 716.5

Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

Table 1102.5, Table 1403.2

Standard Specification for Polyethylene (PE) Plastic Tubing

Table 605.3

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

Table 702.3, Table 702.4, Table 1102.7

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC)Plastic Hot- and Cold-Water Distribution Systems

Table 605.3, Table 605.4, Table 605.5, 605.14.2, 605.15.2

Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets

605.21.3, 705.10.2

Specification for 3.25-in. Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

Table 702.1, Table 702.2, Table 702.3, Table 702.4, Table 1102.7

Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

Table 702.3, Table 702.4, Table 1102.4, Table 1102.5, Table 1102.7

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

Table 605.3

Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Non-pressure Piping Components

705.16.4

Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

605.10.1, 605.22.1

Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

705.2.1, 705.10.1, 705.12.2, 705.15

Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

Table 605.5

Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

Table 1102.7

Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-containment Membrane

421.5.2.2

Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-containment Membrane

421.5.2.1

Standard Test Methods for Surface Burning Characteristics of Building Materials

504.7

Standard Practice for Water Conservation Through In-Situ Water Reclamation

1302.1

Standard Practice for the Assessment of Rainwater Quality

1303.15.9

Specification for Corrugated Polyethylene (PE) Pipe and Fittings

Table 1102.5, Table 1403.2

Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

412.1.2, Table 1102.7

Standard Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

Table 605.5

Standard Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC)Plastic Pipe Fittings, Schedule 40

Table 605.5

Standard Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

Table 605.5

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

Table 605.3, Table 605.4

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

Table 605.3, Table 605.4

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

605.23, 705.16

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

605.14.2, 605.15.2

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core

Table 702.1, Table 702.2, Table 702.3, Table 702.4, 705.2.2, Table 1102.4, Table 1102.7

Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

605.21.3, 705.10.2, 705.14.2

Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings

Table 1102.4, Table 1102.5

Standard Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

Table 702.3

Specification for Cross-linked Polyethylene (PEX) Tubing

Table 605.3, Table 605.4

Specification for Cross-linked Polyethylene (PEX) Plastic Hot- and Cold-water Distribution Systems

Table 605.5

Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core

Table 702.1, Table 702.2, Table 702.3, Table 1102.4, Table 1102.5, Table 1102.7

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene Pipe and Tubing

Table 605.5

Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe

Table 605.3, Table 605.4, Table 605.5, 605.20.1

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

Table 605.3, Table 605.4, Table 605.5, 605.20.1

Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

Table 702.1, Table 702.2, Table 702.4, 705.13.1, 901.3

Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications

Table 605.5, 605.13.3, 605.17.3, 605.22.2, 605.22.3

Standard Specification for Coextruded Composite Pipe

Table 702.1, Table 702.2, Table 702.3, Table 1102.4, Table 1403.2

Standard Specification for Folded Poly (Vinyl Chloride) (PVC) for Existing Sewer and Conduit Rehabilitation

717.6

Standard Specification for the Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications

Table 605.5

Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems

Table 702.1, Table 702.2, Table 702.3, Table 702.4, 705.14.1

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table 605.5

Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

Table 702.4, Table 1102.7

Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation

717.6

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

Table 605.5

Standard Specification for Special Engineered Fittings, Appurtenances or Valves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC)Systems

Table 605.7

Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

Table 605.5, 605.20.1

Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems

Table 605.3, Table 605.4, Table 605.5

 Standard Specification for Cold Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe

Table 605.5

Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) to Metal Insert and Plastic Insert Fittings

Table 605.5

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table 605.5

Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Tubing OD Controlled SDR9

Table 605.3, Table 605.4

12″ to 60″ Annular Corrugated Profile-wall Polyethylene (PE) Pipe and Fittings for Gravity Flow Storm Sewer and Subsurface Drainage Applications

Table 1102.4, Table 1102.7

Standard Specification for Pressure-Rated Polypropylene (PP) Piping Systems

Table 605.3, Table 605.4, Table 605.5, Table 605.7, 605.19.1

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/ Cross-linked Polyethylene (PEX AL-PEX) Tubing

Table 605.5

Standard Practice for Rehabilitation of a Sewer Service Lateral and its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner

718.1

Standard Practice for Sectional Repair of Damaged Pipe by Means of an Inverted Cured-in-Place Liner

718.1

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems

Table 702.6

Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

Table 1102.4

Standard Specification for Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

Table 605.5

Standard Specification for 6 to 30 in. [152 to 762 mm] Polypropylene (PP) Corrugated Single Wall Pipe and Double Wall Pipe

Table 702.3

Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

1102.7

 Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

Table 702.3

Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot- and Cold-water Tubing and Distribution Systems

Table 605.3, Table 605.4, Table 605.5

Standard Practice for Internal Non Structural Epoxy Barrier Coating Material Used in Rehabilitation of Metallic Pressurized Piping Systems

601.5

Standard Specification for Chlorinated Poly (Vinyl Chloride)/Aluminum/Chlorinated Poly (Vinyl Chloride) (CPVC/AL/CPVC) Composite Pressure Tubing

Table 605.3, Table 605.4

Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

Table 1102.4, Table 1102.7

Standard Specification for 150 to 1500 mm [6 to 60 in] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

Table 702.3, Table 1102.4, Table 1102.7

Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Propylene (PP) Piping

Table 1102.7

Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems

Table 605.5

Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long Term Watertightness of Cured-in-Place Rehabilitation of Main and Lateral Pipelines

718.1

Standard Practice for the One-Step (Solvent Cement Only) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets

605.14.2, 605.15.2, 705.10.2

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table 605.5

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table 605.5

Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications

Table 702.1, Table 702.2, Table 702.4

Specification for Filler Metals for Brazing and Braze Welding

605.12.1, 605.13.1, 705.5.1, 705.6.1

Cement-mortar Lining for Ductile-iron Pipe and Fittings

605.3, 605.5

Ductile-iron and Gray-iron Fittings

Table 605.5, Table 702.4, Table 1102.7

Rubber-gasket Joints for Ductile-iron Pressure Pipe and Fittings

605.11

Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

Table 605.3, Table 605.4

Ductile-iron Pipe, Centrifugally Cast

Table 605.3, Table 605.4

Ductile-iron Compact Fittings

Table 605.5

Metal-Seated Gate Valves for Water Supply Service

Table 605.7

Rubber-Seated Butterfly Valves

Table 605.7

Standard for Ball Valves, 6 In. Through 60 in. (150 mm through 1,500 mm).

Table 605.7

Double Check Valve Backflow Prevention Assembly

Table 608.1, 608.14.7

Reduced-pressure Principle Backflow Prevention Assembly

Table 608.1, 608.14.2, 608.17.2

Disinfecting Water Mains

610.1

Disinfection of Water-storage Facilities

610.1

Polyethylene (PE) Pressure Pipe and Tubing 3/4 inch (19 mm) Through 3 inch (76 mm) for Water Service

Table 605.3

Cross-Linked Polyethylene (PEX) Pressure Tubing 1/2 inch (13 mm) through 3 inch (76 mm) for Water Service

Table 605.3

Standard Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

Table 702.1, Table 702.2, Table 702.3, Table 702.4, Table 1102.4, Table 1102.5, Table 1102.7

Standard Specification for Coupling for Use in Connection with Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

705.3.3

Non-reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

Table 702.3, Table 1102.4

Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

Table 702.3, Table 1102.4

Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

705.4, 705.16

Macerating Systems and Waste Pumping Systems for Plumbing Fixtures

405.5, 712.4.1

Personal Hygiene Devices for Water Closets

412.9

Plumbing Supply Fittings

412.1, 412.2, 412.3, 412.4, 412.6, 412.8, Table 605.7, 607.4, 608.2

Plumbing Waste Fittings

412.1.2, 421.3.1

Flexible Water Connectors

605.6

Enamelled Cast Iron and Enamelled Steel Plumbing Fixtures

407.1, 410.1, 418.1, 419.1, 421.1, 422.1

Ceramic Plumbing Fixtures

401.2, 405.10, 407.1, 408.1, 410.1, 418.1, 419.1, 421.1, 422.1, 424.1, 425.1

Stainless Steel Plumbing Fixtures

405.9, 407.1, 418.1, 419.1, 421.1, 425.1

Flush Valves and Spuds for Water Closets, Urinals and Tanks

415.4

Hydromassage Bathtub Systems

426.1, 426.4

Anti-Siphon Fill Valves for Water Closet Tanks

415.3.1, Table 608.1

Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

412.3, 412.4, 607.4

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

415.2

Performance Requirements for Water Temperature Limiting Devices

408.3, 412.5, 412.10, 419.5, 423.3, 607.1.2

Vacuum Breakers, Atmospheric Type (AVB)

415.2, Table 608.1, 608.14.6, 608.17.4.1

Pressure Vacuum Breakers, (PVB)

Table 608.1, 608.14.5

Spill Resistant Pressure Vacuum Breakers (SRPVB)

Table 608.1, 608.14.5

Vacuum Breakers, Hose Connection Type (HCVB)

Table 608.1, 608.14.6

Hose Connection Vacuum Breakers (HCVB) with Manual Draining Feature

Table 608.1, 608.14.6

Hose Connection Dual Check Vacuum Breakers (HCDVB)

Table 608.1, 608.14.6

Vacuum Breakers, Hose Connection Type (HCVB) with Automatic Draining Feature

Table 608.1, 608.14.6

Dual Check Backflow Preventers with Atmospheric Port (DCAP)

Table 608.1, 608.14.3, 608.17.2

Reduced Pressure Principle (RP) Backflow Preventers

Table 608.1, 608.14.2, 608.17.2

Double Check Valve (DCVA) Backflow Preventers

Table 608.1, 608.14.7

Double Check Valve Backflow Preventers for Fire Protection Systems (DCVAF)

Table 608.1, 608.14.7

Dual Check Valve (DuC) Backflow Preventers

605.3.1, Table 608.1, 608.14.9

Laboratory Faucet Vacuum Breakers (LFVB)

Table 608.1, 608.14.6

Selection and Installation of Backflow Preventers

312.11.2

Maintenance and Field Testing of Backflow Preventers

312.11.2

Commercial and Residential Drains and Cleanouts

413.1

Plumbing Fittings

408.3, 412.4, 412.5, 415.2, 415.3.1, 423.3, Table 605.7, Table 608.1

Polyethylene (PE) Pipe, Tubing and Fittings for Cold-water Pressure Services

Table 605.3, Table 605.5

Polyvinylchloride, PVC, Injection-moulded Gasketed Fittings for Pressure Applications

Table 605.5

Rigid Polyvinylchloride (PVC) Pipe and Fittings for Pressure Applications

Table 605.3, Table 605.5, 605.21.3, 705.10.2, 705.14.2

Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications

Table 605.3, Table 605.4, Table 605.5

Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing and Fittings for Hot- and Cold-water Distribution Systems

Table 605.3, Table 605.4, Table 605.5

Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems

Table 605.3, Table 605.5, 605.20.1

Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Composite Pressure-pipe Systems

Table 605.3, Table 605.4, Table 605.5, 605.20.1

Polypropylene (PP-R & PP-RCT) Pipe and Fittings for Pressure Applications

Table 605.3, Table 605.4, Table 605.5

Polyethylene of Raised Temperature Resistance (PE-RT) Tubing Systems for Pressure Applications

Table 605.3, Table 605.4, Table 605.5

Acrylonitrile-Butadiene-Styrene ABS Drain, Waste and Vent Pipe and Pipe Fittings

Table 702.1, Table 702.2, Table 702.3, Table 702.4, 705.2.2, 714.2, Table 1102.4, Table 1102.7

Polyvinylchloride PVC and Chlorinated Polyvinylchloride (CPVC) Drain, Waste, and Vent Pipe and Pipe Fittings

Table 702.1, Table 702.2, 705.10.2, 705.14.2, 714.2

Polyolefin and Polyvinylidene Fluoride (PVDF) Laboratory Drainage Systems

Table 702.1, Table 702.2, Table 702.3, Table 702.4, 705.13.1

Plastic Drain and Sewer Pipe and Pipe Fittings

705.10.2, 705.14.2, Table 1102.4, Table 1102.5

PSM Type Polyvinylchloride PVC Sewer Pipe and Fittings

Table 702.3, Table 1102.4, Table 1102.5

Profile Polyvinylchloride PVC Sewer Pipe and Fittings

Table 702.3, Table 1102.4, Table 1102.5

Profile Polyethylene (PE) Sewer Pipe and Fittings for Leak-proof Sewer Applications

Table 1102.5

Profile Polyethylene (PE) Storm Sewer and Drainage Pipe and Fittings

Table 1102.5

Profile Polypropylene (PP) Sewer Pipe and Fittings for Leak-proof Sewer Applications

Table 702.3, Table 1102.4

Water Pressure Reducing Valves for Domestic Water Systems

604.8

Testing and Rating of Grease Interceptors Using Lard

1003.3.4

Sizing, Selection, Location and Installation of Grease Interceptors

1003.3.5

Drinking Water Treatment Systems

611.1, 611.2

Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

705.2.1, 705.3.3, 705.5, 705.10.1, 705.11, 705.12.2, 705.16

Plastic Plumbing Fixtures

407.1, 418.1, 419.1, 419.2, 421.1, 422.1, 424.1, 425.1, 425.1.2

Reduced Pressure Principle Backflow Preventers for Fire Protection Systems (RPF)

Table 608.1, 608.14.2

Rainwater Harvesting Systems

1301.1

Prefabricated Gravity Grease Interceptors

1003.3.7

Non-sewered sanitation systems — Prefabricated integrated treatment units — General safety and performance requirements for design and testing

311.1

Test Method for Evaluating Roof Drain Performance

1102.6

Plastic Plumbing Fixtures

407.1, 418.1, 419.1, 419.2, 421.1, 422.1, 424.1, 425.1, 425.1.2

Ball Valves

Table 605.7

Rainwater Harvesting Systems

1301.1

International Building Code^®

201.3, 202, 307.1, 307.2, 307.4, 308.2, 309.1, 309.2, 310.1, 310.3, 315.1, 403.1, Table 403.1, 403.1.2, 403.3.1, 403.4, 404.1, 407.3, 421.6, 502.4, 606.5.2, 1106.5, 1301.9.3, 1303.6, 1402.1

Solar Thermal System Standard

502.1

Standard for Accessible and Usable Buildings and Facilities

404.2, 410.3

International Existing Building Code^®

102.2.1

International Energy Conservation Code^®

313.1, 607.2.2, 607.5

International Fire Code^®

201.3, 1201.1

International Fuel Gas Code^®

101.2, 201.3, 502.1, 502.1.1

International Mechanical Code^®

201.3, 307.7, 310.1, 502.1, 502.1.1, 612.1, 1202.1

International Private Sewage Disposal Code^®

701.2

International Residential Code^®

101.2

Emergency Eyewash and Shower Equipment

411.1

Butterfly Valves

Table 605.7

Gray Iron Gate Valves, Flanged and Threaded Ends

Table 605.7

Gray Iron Swing Check Valves, Flanged and Threaded Ends

Table 605.7

Ball Valves with Flanged or Butt-welding Ends for General Service

Table 605.7

Cast Iron Plug Valves, Flanged and Threaded Ends

Table 605.7

Bronze Gate, Globe, Angle and Check Valves

Table 605.7

Ball Valves, Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends (incl. a 2010 Errata Sheet)

Table 605.7

Plastic Industrial Ball Valves

Table 605.7

Copper Alloy Gate, Globe, Angle and Check Valves for Low Pressure/Low Temperature Plumbing Applications

Table 605.7

Design and Installation of Oxygen-Fuel Gas Systems for Welding, Cutting and Allied Processes

1203.1

Compressed Gases and Cryogenic Fluids Code

1203.1

National Electrical Code

502.1, 504.3, 1113.1.3

Health Care Facilities Code

1202.1

Water Well Construction Standard

602.3.1

Commercial Warewashing Equipment

409.1

Plastic Piping System Components and Related Materials

303.3, 611.3

Manual Food and Beverage Dispensing Equipment

426.1

Drinking Water Treatment Units-Aesthetic Effects

611.1, 611.3

Residential Cation Exchange Water Softeners

611.1, 611.3

Equipment and Chemicals for Swimming Pools, Spas, Hot Tubs and Other Recreational Facilities

1302.8.1

Drinking Water Treatment Units—Health Effects

611.1, 611.3

Reverse Osmosis Drinking Water Treatment Systems

611.1, 611.2, 611.3

Drinking Water System Components—Health Effects

410.1, 412.1, 605.3, 605.4, 605.5, 605.7, 605.12.3, 605.13.6, 608.12, 611.3

Drinking Water Distillation Systems

611.1

Residential Dishwashers

409.1

Onsite Residential and Commercial Water Reuse Treatment Systems

1302.6.1

Valves for Cross-linked Polyethylene (PEX) Water Distribution Tubing Systems

Table 605.7

Drinking Water Systems Components—Lead Content

605.2.1

Testing and Rating Procedure for Hydro Mechanical Grease Interceptors with Appendix of Installation and Maintenance

1003.3.5

Testing and Certification for Grease Interceptors with FOG Sensing and Alarm Devices

1003.3.5

American National Standard: for Sanitation: Non-Sewered Waste Disposal Systems: Minimum Requirements

311.1

Drinking-Water Coolers—with Revisions through July 2020

410.1

Waste Disposers—with Revisions through September 2021

416.1

Industrial Control Equipment—with Revisions through July 2021  

314.2.3

Standard for Test for Surface Burning Characteristics of Building Materials

504.7

Hydromassage Bathtubs—With Revisions Through December 2017

426.1

WaterSense: Tank-Type High Efficiency Toilet Specification

202, 420.1

WaterSense: Specification for Flushing Urinals

202, 419.1

WaterSense: High-Efficiency Lavatory Faucet Specification

202